Tray & Related

This flat metal tray is a replacement nonstick oven tray that gives you a flat cooking or drip surface for baking and roasting. It restores a level surface for pans and helps contain spills for easier cleanup. What it does:

• Provides a flat, rigid surface for baking, roasting, or catching drips beneath racks
• Restores proper fit when original tray is bent, warped, or missing
• Helps reduce food contact with oven floor and collects spills to prevent messes
• Nonstick finish eases cleanup when coating remains intact

• Install on the oven rack or support as shown in your owner's manual; ensure it sits flat before heating
• Allow tray to cool before handling to avoid burns
• Do not use abrasive pads or metal utensils on the nonstick surface to avoid damaging the coating
• Inspect coating for chips or flaking; replace if coating is compromised to avoid contamination

Connects the motor to the glass tray for smooth turntable rotation. Replace if your shaft is broken, worn, or causing the tray to wobble or scrape.

This metal wire rack sits inside the microwave cavity and provides an additional cooking level, allowing you to heat or cook multiple items at once. It is designed specifically for microwave use with supports that keep it properly elevated. Replace this rack if it is bent, rusted, or has damaged feet, which can cause arcing or uneven cooking.

Replacement glass turntable tray for your microwave. Installs on the rotating support hub inside the cavity. Order when cracked, shattered, or broken.

This is a nonstick metal grill tray designed for use in a microwave or combination cooking appliance. It serves as a cooking surface that allows grease and drippings to drain away from food during grilling or broiling functions. Replace this tray if the nonstick coating is peeling, the metal is warped, or the grill no longer sits properly on the turntable.

This replacement tray catches and channels water under the refrigerator to prevent leaks and allow proper evaporation. It restores proper drainage and helps avoid standing water that can cause odors or damage. What it does

• Collects defrost and condensate water from the evaporator area to prevent puddling under the cabinet
• Directs water toward the evaporator/drain system so it can evaporate safely
• Helps keep the refrigerator floor and surrounding cabinetry dry
• Stops common symptoms like water pooling beneath the unit or musty smells from standing water

• One replacement tray

• Disconnect power to the appliance before any service
• Remove lower kick panel or shelves as required to access the tray; allow any standing water to drain into a bucket
• Inspect mounting location and drain channel for debris; clean before installing the new tray
• Seat the tray fully and restore panels; plug in and check for proper drainage during the next defrost cycle

Connects the turntable motor to the drive shaft in your microwave. Replace if cracked, broken, worn, or fused to the motor, preventing turntable rotation.

Replacement drive coupler for microwave turntable systems. Connects motor to turntable shaft. Replace if cracked, stripped, or broken to restore rotation.

This wire rack assembly provides a sturdy, removable shelf for your oven, giving stable support for cookware and bakeware and restoring proper shelf placement and clearance. What it does

• Replaces a bent, damaged, or missing oven shelf so pots and pans sit level during baking and roasting
• Restores smooth sliding and correct clearance for consistent cooking results
• Helps prevent cookware from tipping or shifting on weakened racks
• Fits into existing rack supports or side rails for secure positioning

• Remove power to the appliance and allow it to cool completely before installing
• Slide the rack into the oven rails or supports until fully seated; it rests level
• Wear gloves to avoid pinches or sharp edges while handling the rack
• No special tools usually required; refer to your owner's manual for model-specific guidance

Nonstick grille tray pan for microwave ovens with broiling/grilling capability. Replace your cracked, worn, or missing tray for even cooking results.

Turntable roller assembly support for microwaves. Holds and guides the glass tray as it rotates. Replace if cracked, broken, or worn from use.

This guide supports the glass turntable tray inside the microwave, allowing it to rotate smoothly during cooking. It sits on the microwave floor and holds the tray at the correct height for even heating. Replace this part if the turntable wobbles, does not rotate properly, or if the guide is cracked or broken.

Replace your microwave's coupler holder if it's cracked, broken, or missing. This support piece secures the drive coupler to ensure proper operation.

Wire rack for microwave ovens. Installs inside the cavity to provide an elevated cooking surface. Replace if bent, rusted, or missing from your unit.

This plastic component sits in the center of the microwave floor and supports the rotating glass tray. Replace when the tray wobbles, doesn't rotate smoothly, or the support is cracked or broken.