Wall Oven Igniter

The Spark Electrode is an OEM part for Whirlpool ranges. It is responsible for generating the spark that ignites the gas in the burners, allowing for efficient and reliable lighting of the stove. The spark electrode is located near the burner and produces a high-voltage spark to ignite the gas.

Causes of a bad spark electrode can include wear and tear over time, buildup of food debris or grease that can interfere with the spark, and damage from cleaning or handling. Electrical issues can also cause the electrode to fail.

Symptoms of a bad Spark Electrode include:

• The burner not igniting
• Weak or no spark
• Clicking sound without ignition
• The burner lighting inconsistently

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This oven igniter lights the gas burner when the control calls for heat, restoring reliable ignition and consistent baking performance. Replace it if the oven won't light, preheats slowly, or the flame won't stay on. What it does:

• Provides the ignition source for the oven's gas burner during bake cycles
• A weak or failed igniter can cause no heat/no bake or intermittent ignition
• Can contribute to extended preheat times and burners that light then go out
• Visible cracks, burned spots, or damaged leads on the igniter are common failure signs

• One oven igniter

• Disconnect power and shut off gas before servicing
• Allow components to cool; handle the igniter's ceramic/element carefully to avoid damage
• Install in the original position; correct placement relative to the burner is critical
• After reassembly, restore utilities and test for proper ignition; leak-check any disturbed gas fittings

By GE. Length - 3.72". Replaces any flat oven igniter (excluding blue ceramic igniters).

This spark electrode mounts at the bake burner and creates the ignition spark to light the oven flame. Replacing a worn or cracked electrode restores fast, reliable bake ignition and consistent oven temperatures.

• Generates a high-voltage spark to ignite gas at the bake burner
• Helps correct symptoms such as no heat on Bake, repeated clicking without ignition, or intermittent bake heating
• Wear, contamination, cracks, or misalignment of the tip can prevent proper ignition
• Restores dependable oven lighting and reduces delayed ignition

• Disconnect power and shut off gas supply before servicing
• Remove oven racks, oven bottom panel, and flame spreader to access the bake burner area
• Note wire routing and electrode position; transfer any bracket as needed and secure the new electrode
• Align the electrode tip close to the burner, then restore power and test ignition

The Ignition Device is an OEM part for Bosch gas cooktops. This ignitor is responsible for sparking the burners to safely ignite the gas flow and initiate the cooking process.

The ignition device works through a high-voltage electrical arc that produces a spark near each gas burner valve whenever a cooktop burner is turned on. This spark reliably ignites the gas, allowing full and consistent burner flame.

Causes of a bad ignition device can include defects in the electronic components, wear and tear of the electrode tips over time, or issues preventing a strong enough spark from occurring.

Symptoms of a bad ignition device include:

• Burners that will not light or remain lit
• Repeated lighting attempts required before a flame is produced
• Inconsistent or intermittent ignition between burners
• Burners that light but then extinguish unexpectedly

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Spark Electrode is an OEM part for Whirlpool gas ranges and cooktops. It is responsible for igniting the gas burner by generating a spark when the burner knob is turned to the ignite position, ensuring efficient and safe ignition of the gas.

Causes of a bad spark electrode can include exposure to high heat, accumulation of food debris, or wear and tear over time. These issues can prevent the electrode from producing a proper spark, leading to ignition problems.

Symptoms of a bad spark electrode include:

• Burner not igniting or taking longer to ignite
• Weak or no spark visible when igniting the burner
• Clicking sound without ignition
• Intermittent ignition problems

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This is a replacement spark electrode. This is a genuine OEM part made by Whirlpool and has been sourced directly from the manufacturer. This part is intended to replace a burnt-out or faulty spark electrode in various models of gas stoves and ranges.Spark electrodes provide a spark that will catch the gas in order to ignite the burner. If the burners will not light, or the gas igniter glows but won't ignite, this part may be the issue. It is always recommended that the appropriate safety precautions are adhered to when attempting to fix any appliances. Please make sure that the stove is entirely disconnected from gas and power before starting the repair work. Proper tools may be required to install this part. For more accurate information on how and where to install this spark electrode, the appropriate owner's manual and included diagrams should be referenced.As an authentic replacement part, this spark electrode is suitable for use on several different models of refrigerators manufactured by Whirlpool, Maytag, KitchenAid, Amana, and other Whirlpool brands. This is a genuine part made of high-quality, durable, non-corrosive materials and is sold individually.

The Electrode is an OEM component specifically designed for select Bosch gas range models featuring a pilot ignition system. Located near the gas valve, it initiates sparking to reliably light burners on demand. Consistent placement ensures safe and dependable burner ignition.

Symptoms of a faulty electrode commonly involve failure to produce sparks stopping burners from lighting properly. Regular flareups increase electrode wear warranting timely replacement.

Causes of a bad electrode include normal arc erosion reducing spark output. Deposits inhibiting consistent contact necessitate cleaning or a component change.

Causes of a bad electrode can involve:

• Burners lighting sporadically or requiring multiple ignitions
• Pilot lights repeatedly going out between uses   
• Inability to ignite burners for cooking

This OEM Bosch part is also compatible with some Dacor, Thermador, and Blomberg gas ranges. 
 

This igniter lights the gas at a burner. Replacing a worn or cracked igniter restores quick, consistent ignition so your gas range or cooktop lights reliably and heats as expected without repeated tries.

• Provides the ignition source to light burner gas when heat is selected
• Supports consistent flame start-up for reliable cooking performance
• Common symptoms include: burner won't ignite, delayed or intermittent ignition, or needing to light manually
• Visual clues can include a cracked insulator or damaged igniter tip/element

• Disconnect power and shut off gas before servicing; allow the appliance to cool completely
• Access the igniter per your model; note wire routing and mounting before removal
• Transfer any reusable mounting clip/grommet from the old part to the new one
• Handle the igniter carefully and avoid touching the element/tip; ensure secure connections and test ignition before reassembly

This surface burner spark electrode creates the arc that lights the gas at the burner. Replacing a worn or cracked electrode restores quick, reliable ignition on your gas cooktop or range.

• Generates a high-voltage spark to ignite the surface burner gas
• Sits beside the burner head and fires when a control knob is turned
• Common symptoms: burner won't light, no/weak/intermittent spark at one burner, visible cracks in the ceramic, arcing to the cooktop
• Helps restore consistent ignition when the original electrode is damaged or contaminated

• Disconnect power and shut off gas; allow the appliance to cool completely
• Remove burner cap and head to access the electrode; access may be from the top or beneath the cooktop per your model's service information
• Transfer any mounting hardware from the old part; route the spark wire as originally and seat the tip at the same gap/position to the burner
• Avoid striking or overtightening the ceramic insulator; keep the tip clean and dry during installation

The Top Burner Igniter is an OEM part for Whirlpool gas ranges. This igniter is responsible for generating the spark needed to ignite the gas burner, ensuring efficient and reliable cooking performance. It plays a crucial role in the overall functionality of the stove, enabling the burners to light quickly and safely.

Causes of a bad top burner igniter can include wear and tear from regular use, buildup of food or grease that affects its operation, damage from cleaning, and electrical issues such as power surges or faulty wiring.

Symptoms of a bad top burner igniter include:

• Burners not lighting or taking a long time to ignite
• Weak or no spark visible at the igniter
• Clicking sound without ignition
• Uneven flame or burners not staying lit

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The High Voltage Harness & Electrodes is an OEM part for GE gas ranges. This burner harness and electrode assembly makes sure there is proper operation of the range's gas surface burners. The harness distributes electrical current from the range's control board to ignite the burners via the electrode spark igniters. Without functioning electrodes and an intact harness, gas burners will not light and be unable to operate safely.

Causes of a bad high-voltage harness and electrode assembly can include damage from corrosion, cracks or shorts in the wiring, or deterioration of the electrodes over many ignitions and heat cycles.

Symptoms of a faulty harness and electrodes include:

• Gas burners that will not light or ignite
• Surface elements that intermittently fail to function
• Burners that produce an inconsistent or irregular flame

This GE replacement part is compatible with Hotpoint, RCA, and some Kenmore models.

This dual-burner surface spark igniter lights two adjacent gas burners on your range or cooktop. Replacing a worn or cracked igniter restores quick, reliable ignition and consistent lighting across the pair, reducing long clicking or failed starts.

• Generates a high-voltage spark at two electrodes to ignite gas at both burners in the pair
• Helps resolve: surface burner won't light, only one of the two lights, intermittent/weak spark, or excessive clicking before ignition
• Often needed when ceramic insulators are cracked, tips are damaged, or the igniter is shorting to ground
• Designed for units that use a shared dual-burner igniter assembly

• Disconnect electrical power and shut off gas before servicing
• Remove grates, burner caps, and bases to access; lift the cooktop or burner deck as required
• Transfer any mounting hardware and align electrodes with burner ports; avoid stressing the ceramic
• Reconnect leads securely, reassemble, and test burner ignition

This is the spark electrode used to ignite the gas in the oven. It creates a spark at the burner to light the flame so your oven can heat reliably.

• Generates the spark that lights the oven burner
• A failed electrode can cause no heat, delayed ignition, or the oven not lighting
• Intermittent sparking or clicking without ignition may indicate a worn or cracked tip
• Carbon buildup or damage to the ceramic insulator can prevent proper ignition

• Disconnect power and shut off gas before servicing
• Access the burner area, note wire routing, and handle the ceramic insulator carefully
• Position the electrode tip at the specified gap to the burner per service literature
• Test for proper spark and burner ignition after reassembly

Amperage range 3.2 to 3.6

This spark igniter creates the arc that lights the gas burner, restoring quick, reliable ignition in your range or oven. Replacing a worn electrode helps eliminate hard starts, intermittent lighting, and nonstop clicking.

• Generates a high-voltage spark at the burner to ignite gas
• Helps resolve burner won't light, delayed ignition, or intermittent sparking
• Can reduce continuous clicking caused by a weak, damaged, or mispositioned electrode
• Typical signs include no visible spark or a cracked ceramic insulator

• Disconnect power and shut off gas; allow the appliance to cool before service
• Handle the ceramic insulator carefully; avoid bending or striking the electrode tip
• Position the tip near the burner port; ensure a solid ground and secure bracket
• Reconnect the lead firmly, then test for a strong spark before reassembly