White Westinghouse Parts

• Frost buildup

Arrived on time and was a good fit. no problems at all thank you Read more

We ordered the parts we needed, and received it with-in a week. My husband was able to covert the stove in one evening. Read more

In short - I replaced the evaporator fan motor and the evaporator fan blade. The Appliance Parts Pros website was extremely helpful to me. Here's how. 1. The site helped me identify that even though my Freezer says it's a Frigidaire, it's actually an Electrolux. 2. The site identified the potential screech causing parts. (I didn't take a chance, I bought all three) It was a worthwhile investment. My freezer is 20 years old so it deserved some help. 3. The site provided guidance videos (not... Read more

Main problem was worn bearings in the motor, which was replaced. Additional issues were worn pulley on tensioner and impeller slipping on motor shaft. Pulley was replaced and hose clamp was used to secure blower on shaft. Read more

Took cover completely off and tried putting back, could not match up left screw with available screw hole. Tried many different configurations and sequences to make this happen. watched a video on changing the front panel, the door in it had four screws, mine 2, no help there. Searched on the hyperextending issue, found an article about dogs and kids [had both here] climbing on the door and to check the springs and linkages. Linkages intact both sides, R [opposite] side spring very stretched.... Read more

Heating element nut had cracked causing a leak. Rather than run right out and buy a new one, I found the cracked nut and replaced it for about 11.00. Thank you Appliance pros. Quick shipping. Read more

Ordered new Ignitor / Orifice and screws Mike was a great resource, he helped me thru the project. Read more

We ordered a igniter and a new regulator. My husband installed the parts it works great now. Read more

I had the original sensors in my Frigidaire, which were now about 18 years old. The water dispenser would work, but I would have to push in the lever and then draw it back until it found that "sweet spot." I finally got annoyed enough with the problem that I looked online. I almost purchased the dispenser actuator (the paddle), and glad I didn't because it was not the problem. Unless your lights are out, or it broke, the culprit will be these little dispenser switches which get pressed... Read more

I used the internet and checked a dry fuse, and it tested ok. Checked the start switch, ok. So it had to be the motor. Sharon at the company agreed. Motor, and belt arrive very fast. ordered the belt because, if I had it apart why not change it. Internet also helped get the dryer apart. Found on u-tube a repairman cut a hole in the side to gain easy access. This dryer is not easy to work on, but this helped, and will make further repairs much easier. Using the internet, and... Read more

• Marks left on clothes
• Noisy

I'm new to how a dryer works, so I just started taking it apart to see what exactly was causing it. The video examples on the APP website were all amazing. It gave me a good idea of what I was getting into and showed me the common repair issues. The dryer being 12 years old, I was on the fence about repairing or replacing. However, once I got a list of parts I might need and getting the confidence by watching the videos, I said "what have I got to lose." The cause of the scraping and loud... Read more

• Not dispensing water

I OBSERVED UPON OPENING THE COVER THAT FILTER ASSEMBLY COVER HAD CRACKED. ORDERED NEW COVER AND REPLACED IT. LEAK HAS STOPPED. Read more

• Will not drain

Replace the drain pump after watching a video demonstrating the process. The washing machine had run properly and emptied, so I was surprised how much water remained in the pipe after disconnecting the old pump. Plan on having 2-3 large towels underneath before removing it. The most difficult part (and most irritating) was replacing the intake and outtake hoses with the existing spring clamps. The drain hose into the pump took almost twenty minutes to attach properly. If the hardware store was... Read more

Initially I noticed the crusher drum was cracked and broken so I replaced the drum the retaining nut on the end of the auger and the circlip and washer. it worked fine for a time and then the drum began free wheeling. upon further inspection I discovered the retain nubs on the auger had worn down allowing the blade to slip down the auger body. so I replaced the auger, drum, drive blade, and drive cam. I recommend if you gave a problem with the ice dispenser you break down and inspect the entire... Read more

Ordered new side bracket & glass-- had them in 2-days -- as we lived not far from the parts warehouse ( 200 miles). Had everything cleaned up prior to the pats arrival & was back in business --- 1/2 hour after receiving them. Great service and for very reasonable prices !! Read more

I snapped the shelves in place. It was very easy! Read more