White Westinghouse Parts

Burner element was broken and partially melted. Didn't know if element or switch or kettle started it. Switch smelled burnt and bad; "burner on" light was on regardless of switch position. Traded with another burner switch; light went out. Ordered new infinity switch, burner element, plug for burner element, & drip pan. Watched Appliance Parts Pros videos (the plug one simplified that part). Replaced items. Range works fine. Received parts in one day with regular shipping. Great service! Read more

• Takes too long to dry

Get some acetone at a Hardware Store before you start. A pint will do. Unplug the dryer from 110 VAC. Pull the top off of the dryer, by lifting it from the front first. It is attached with snap metal fittings. Do not completely remove the top, just tip upright to gain access to the front interior of the dryer. Before you pull any wires from the door switch, record which color wires go to which terminals on the door switch. If you reassemble the connections incorrectly, the gas value will... Read more

I tried swapping the cables around by putting the cables from the burners that would light onto the ones that didn't light. When I did that the problem would move. So this is how i determined that the issue was with this module and not the burners or cables. Once this new module arrived it was simple to disconnect the old one and put the cables back on the new one. I tested it (holding by breath!) and then all of the burners started. HOORAY! Read more

I replaced it with the Mfg. parts bought from AppliancePartsPros.com. The job went very smoothly, I received the parts a day and one-half after ordering them from your website. I am an HVAC contractor and was so pleased with your service that I'll use you again and again. Read more

My tenant thought that the oven safety valve was bad, but after some research, I found that the transfer of heat from the igniter had to be sufficient enough to cause the valve to open.Your agent confirmed this and reassured me that even if the igniter was glowing, there was a 99% chance that it wasn't getting hot enough. I ordered the igniter, and also the safety valve just in case, as we were going to be fixing this on Christmas eve, so the oven could be used for Christmas dinner. Your agent... Read more

• Won't start

Replaced igniter and orifice assembly, and replaced spark module. Used the video for help, but the video doesn't show the top cover piece that needs to be taken off first. Also the screws for the igniter set were stuck from old grease or something and had to be drilled out. Overall the project was well worth my time for the cost vs replacement decision. AppliancePartsPros.com makes it so easy to choose a part and guesstimate the probably of choosing the right one. Read more

My husband took the door apart replaced hinges in less than 15 minutes. Very easy to do yourself rather then paying a lot of money for someone to come out to do it for you. I would have to say that the customer service was very helpful told me exactly what I needed. Read more

Gotta love the inter-webs and youtube.com I did a couple of searches and some troubleshooting. Everything pointed to the damper assembly and thermo so I ordered them as well as the new versions of the flimsy plastic drawer shelves, while I was working out of state during COVID. I had the parts waiting for me at the house. Rolled in Sunday, 22 minutes later, damper and thermo installed. The fridge is cooling. Today is Tuesday and everything is back down to temp. knuckle bump. Read more

The blower wheel center was worn down and spinning freely on shaft. Removing front covers, controls and brackets gave access to blower, which front half came off removing screws. (One screw underneath bracket) Pushed new blower on. (It's keyed and has small tabs that line up with groove on shaft). Installed clamp, reassembled and tested. Don't forget to pull the plug out before working on any appliance. Read more

• Spins slowly

With more difficulty and frustration than expected but it works fine now. Things learned: 1. Order only 3 replacement pins. One comes with the shocks that you can't be sure you see in the picture. 2. A circuit board in a plastic box mounted to the floor, left rear, must be removed by two screws to be able to get pliers onto the head of the pin more easily. This helps installation too. 3. A 1/2" deep socket pushed onto the retaining tab of the pin stays there while you pull with pliers from the... Read more

Replacement tray from Appliance Parts Pro. Read more

Fixed the new glass in the frame is so easy Read more

I wasn't sure if it was the door being warped, the spring return being worn, or the rotary damper failing, so I ordered all to update the door mechanism. I also ordered a new micro switch since one of the switches had started to require more and more pressure to actuate. Figured I'd fix it at the same time. Repair was very straightforward and the videos available on this and other repair sites were very helpful. I found a video that showed replacing the door mechanism on a nearly identical... Read more

• Element will not heat

When I called customer service your representative at Appliance Parts Pros was able to help me diagnose the problem and order the two parts that I needed. both parts arrived the next day and with helpful tutorial videos I was able to replace both the Surface Unit Switch and the Universal Element in less than 45 minutes. Thanks so much for the great service and the money you saved me. Read more

Replace the sprayer in the middle of the dishwasher, the problem was the grommet on the back of it but it's not available individually. Read more

• Won't start
• Touchpad does not respond

Replaced old knob with new knob Read more