Whirlpool Control Board

The Coin Slide Interface is an OEM part for Whirlpool commercial washers. It is a component that allows users to insert coins or tokens to activate the machine and initiate the laundry cycle.

Causes of a faulty coin slide interface can include regular wear and tear, damage due to misuse or vandalism, or electrical component failure. These factors can result in issues such as coin rejection, incorrect coin counting, or the inability to start the machine using coins.

Symptoms of a Bad Part:

• Will not start
• Not washing properly
• Timer will not set

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Dryer won't advance through cycles or keeps running after finishing? This timer controls cycle sequencing and shutoff. Typical DIY repair in 15 minutes.

Compressor clicking on and off every 5 minutes? Freezer warming up? This inverter control board regulates compressor operation in modern refrigerators.

Fix refrigerator temperature issues, display failures, or defrost problems. This control board manages cooling cycles and temperature settings.

Fix a washer that won't advance cycles or spin with a new timer. Controls wash, rinse, and spin phases. Common DIY repair with clear instructions.

Washer stops mid-spin or shows F6E1 error? The motor control board regulates drive motor speed and direction. Most DIYers replace it in 15-30 minutes.

This is a Whirlpool range control board. It manages and monitors temperatures for the range and features a digital display and user interface buttons. The control board can short out due to power surge or exposure to excessive heat. For example, if the oven's self clean function is run too long or too frequently, parts of the control board could melt or otherwise malfunction.Before installing this part, be sure to cut power to the appliance and allow it to cool completely. The stove may need to be pulled away from the wall to access the screws holding the control panel in place. Remove the screws from each side of the control panel to gain access to the old control board. Disconnect any wire harnesses connected to it and remove any screws mounting it in place before installing the new part.This is a genuine OEM part compatible with ranges manufactured by Whirlpool brands, including Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and others. This product is just the panel and contains no additional parts or hardware.

This is a high-quality refrigerator power supply board. It's an internal component that is made to control the refrigerator functions. This part is made with small precision parts to help with timing defrost and cooling cycles. This part can be damaged or malfunction and stop operating correctly. This may prevent the refrigerator from running, cause strange sounds, or cause the refrigerator to run at the wrong temperature.If this part is damaged, it will need to be replaced. Before replacing the power supply board, make sure the refrigerator is unplugged from the wall. The process will require a flathead screwdriver and a nut driver. Use the tools to unthread the screws on the access cover. Depress the retaining tab to remove the inner cover and disconnect the wires. Press the tab to release the power supply board and snap in the new component. Make sure the wires are properly connected and reassemble.This genuine OEM replacement part is sold on an individual basis. It is directly acquired from the manufacturer and is designed to be compatible with refrigerators made by Kenmore, Whirlpool, Maytag, and KitchenAid.

If your mixer won't start smoothly or speed settings aren't accurate, this speed control board regulates motor power. DIY-friendly replacement.

Fix a refrigerator that won't cool, clicks repeatedly, or has a blank display by replacing the main electronic control board. Moderately difficult repair.

Oven not heating, switches to broil instead of bake, or buttons unresponsive? The control board regulates bake functions and temperature settings.

Microwave not heating or showing F1 E5 error? This inverter board converts voltage to power the magnetron. Requires tech sheet for testing procedures.

Dishwasher won't start or shows error codes? The electronic control board regulates all cycles and functions. Moderate difficulty repair.

Fixes refrigerator not defrosting or freezer icing up. This adaptive defrost control board manages defrost cycles. DIY-friendly repair.

Fix a washer that stops mid-cycle or won't advance through wash phases. This mechanical timer restores proper cycle sequencing. Moderate DIY repair.

Dishwasher won't start, lights blinking, or cycles not completing? The electronic control board manages all wash functions. Moderate DIY repair.