Whirlpool Control Board

Fix a washer that won't start, cycle properly, or respond to controls. This control board replacement restores normal operation. Moderate DIY repair.

Fix F1, F2, or F5 error codes, oven won't start, or shuts off mid-cycle. This range control board manages timing and sequences. Moderate DIY repair.

This defrost timer cam replaces the plastic cam on a mechanical defrost timer. It restores the timer's changeover between cooling and defrost, helping prevent frost buildup on the evaporator and temperature swings inside the refrigerator.

• Mounts on the timer shaft to actuate the internal switch between cooling and defrost
• Helps resolve issues like heavy frost on the evaporator, warm fresh food section, or a unit stuck in defrost/run
• Corrects timer advancement problems caused by a stripped, cracked, or missing cam
• Typically installed with the defrost timer in the control housing or rear service area

• Disconnect power before servicing
• Access the defrost timer and note the original cam's orientation for reference
• Remove any retainer, pull the old cam straight off, and press the new cam fully onto the shaft without forcing
• Reassemble, then manually advance the timer to confirm it switches modes before restoring power

Fix an oven that won't heat, shows error codes, or has unresponsive controls. This main control board coordinates timing and powers key components.

This coin chute guides coins from the slide into the coin mechanism so the machine can register payment and begin a cycle. Keeping the chute intact and aligned helps prevent jams and misfeeds in coin-operated laundry equipment.

• Directs coins from the slide to the coin mechanism to register payment
• Helps ensure smooth coin drop, reducing bounce-back and misfeeds
• Common fix when coins jam, fall into the cabinet, or the unit won't start after payment
• Replace if cracked, bent, corroded, or missing

• Disconnect power; shut off gas before service
• Open the coin housing/slide assembly and retain existing hardware
• Install the new chute in the same orientation; align with slide and mechanism, then secure
• Test with sample coins to ensure proper drop and operation before returning to service

Fix temperature control issues or defrost problems with this refrigerator control board box. Replaces faulty control electronics. Moderate DIY repair.

Fix a washer that won't advance cycles, skips spin, or stops mid-wash. This timer controls cycle progression. Straightforward DIY repair for most users.

Fix error codes and non-responsive controls with this gas range electronic control board. Regulates oven and cooktop functions. Moderate DIY repair.

Washer won't advance cycles or stops mid-cycle? This timer sequences fill, wash, drain, and spin stages. Moderate DIY repair restores cycle control.

Fix unresponsive controls, blinking displays, or oven won't heat. This electronic control board restores full function. Straightforward DIY install.

Fixes inconsistent temperatures, erratic defrost cycles, and appliance that won't start. This main control board restores normal refrigerator operation.

Cracked or damaged control panel trim? This escutcheon covers and protects control switches from grease and spills. Simple install, reuse screws.

This electronic control board is the central module that runs your dishwasher's cycles. It controls power and timing so the unit fills, washes, drains, and dries correctly—restoring normal operation when the original board has failed.

• Manages cycle timing and options, routing power to the wash motor, drain pump, water inlet valve, and heating circuit
• Interfaces with sensors and the door latch to start and advance cycles
• Monitors faults to help protect components and ensure proper operation

• Disconnect power at the breaker and verify no voltage before service
• Access location varies by model
• Use ESD precautions; move connectors one at a time to the matching terminals
• After reassembly, run the unit's diagnostic/service cycle per the tech sheet to verify operation

Fix a worn or cracked start button area on your trash compactor with this peel-and-stick control panel insert. Easy 5-minute DIY repair restores appearance.

This is a mechanical defrost timer that controls the automatic defrost cycle of the refrigerator. It periodically shuts off the compressor and energizes the defrost heater so frost can melt, helping maintain proper cooling performance.

• Cycles the unit between cooling and defrost at set intervals
• Stuck or failed timers can cause warm temperatures, heavy frost, or continuous running
• Can also cause short-cycling or no-cool if contacts fail

• Disconnect power before servicing
• Access is typically from the control housing or rear service area; note wire positions before removal
• Replace one-for-one with the same terminal orientation; do not force the cam
• After install, allow one full cycle to verify defrost operation

Fix a washer that stops mid-cycle or won't advance to drain and spin. This mechanical timer controls wash cycle sequencing. Moderate DIY repair.