Admiral Parts

Had to take the back cover off. It was very tight to remove the fan that sat in the drip pan but did get it off, was able to apply the same level of cursing and got the new pan installed, installing the drain tube was a breeze. Found the parts price very reasonable. Hoping the Whirlpool redesigned the pan so I won't have to do it ever again. I was surprised at how bad the quality of their original part was. Probably saved myself $150.00 on buying the part and doing it myself Read more

Replaced the ice level arm Read more

First had to clean inside the empty freezer, that was the hard part. removed old gasket and cleaned inside the track in the door. had the new gasket well warmed and in the right shape. put new gasket in track. seating it firmly. It was very easy. I did watch a couple of online videos to get the general idea of what it detailed. While I was at it I cleaned the coils with the brush I also bought with the gasket, worked great. all in all if you get organized before hand and take your time,... Read more

• Noisy

I just wanted to put my experience here for all to see. I have a Maytag Neptune, MAH5500BWW, one of the original ones. I bought it back in 2002 and it has done many many loads of wash faithfully. So when the bearings started to get loud I thought it best to replace them, the seal kit and the belt. I did my research as best I could and decided to order the OEM parts from an appliance supplier. If you are replacing the bearings, watch on line videos prior to performing the job. It will... Read more

• No heat or not enough heat

The root cause was the front glides. They were virtually gone, and the drum was on metal to metal. So I replaced them with a front glide kit. I also replaced the belt, rear rollers, and lint screen. I am happy to say all the parts fit perfectly, and I couldn't find a better price anywhere else. I will definitely keep you on file for the next time I need appliance parts! Thank you! Sincerely, pw Read more

All I needed was a $5 piece to fix my fridge, but without it I couldn't even us it. I ordered the part after 4:00 pm and had the new part shipped from Kentucky to NJ and had it by 10:00 am the next morning! Amazing! Great company. Read more

Our dryer suddenly began overheating while drying. Outside of the dryer cabinet was uncomfortably warm to the touch, dryer drum was hot, charred smelling laundry. Based on what I read it was likely one of two things - a failed cycling thermostat or a shorted heating element. First I cleaned the vent hose and ducting to ensure good airflow, which I had. I opened the circuit breaker first, then took off the door and front cover. I started with a thorough cleaning of the dryer with a vaccuum... Read more

Through 15 years of vibration, the Cycling Thermostat evidently had degraded to the point where one electrical connection or more came loose and caused a short. There is also a possibility that the Bakelite section of the Dryer Cycling Thermostat body separated from the metal base, simultaneously exposing all four connections to a short. The thermostat literally exploded into chunks and dust. There was a heavy arcing and then, thankfully, the thermal fuse blew and shut down power to the short... Read more

I replaced the part i ordered and it worked great! Read more

• Will not drain

Checked the circuit board to see if R11 was burnt and it was. They told me if the wax motor had a brown tip that I would have to replace the Machine control circuit board as well as the Wax motor. I ordered the new parts put them in and it worked. Read more

I first wanted to get the dishwasher running, before ordering the spring links. So I disassembled the pump / motor assembly to determine the reason the motor would not start. My wife cleaned all of the parts in the pump assembly. I took the motor apart and discovered that the lower bearing ( a sleeve type bearing) was dry and dirty, and was the culprit for the motor seizing. I cleaned up the bearing and lubricated it with SAE 20W. I also packed felt inside the cavity adjacent to the bearing.... Read more

There was a horrible screeching noise coming from the washer, and upon inspection I found that the retaining nut that attaches the cam to the machine was either improperly tightened to begin with or had worked itself loose causing the cam to wobble and the belt to work down the cam. The cam gear teeth became worn and the belt worked itself half off the cam and cut a hole in the protective plastic screen containing the whole ensemble. I purchased the belt, shield and cam kit. The parts are... Read more

• Door sweating

New seal, old one pulled out easy and new one pushed into place. Read more

• Door won't close
• Shuts off too soon
• Doesn't shut off
• Takes too long to dry

Ordered a new clip and installed it. Easy to do. Unplugged the dryer. Removed the front. It is only held on by two screws. Removed wires to the door switch. removed the female end (it had the broken male piece in it. Inserted the new female part in the front, clipped in the male part into the door and reconnected the door switch wires, screwed the front back on. Job done. Total time was less than 10 minutes. Works like new. Read more

Replaced with thrust bearing kit. Watched your video and it took about 10 minutes to fix. Thanks Read more

These drip pans fit! I had bought some from a local big box store and they didn't fit. I only wish they still made them without the holes in the bottom of the drip pan. How's that supposed to hold a boil-over? But that's the manufacturer. AppliancePartsPros have always sent me orders right on time. Read more