Admiral Parts

These drip pans fit! I had bought some from a local big box store and they didn't fit. I only wish they still made them without the holes in the bottom of the drip pan. How's that supposed to hold a boil-over? But that's the manufacturer. AppliancePartsPros have always sent me orders right on time. Read more

• Gas smell
• Won't start

I replaced the burner head. I turned off power to the stove, although I did not turn off the gas. I gave the old burner head a slight twist counter-clockwise until it lifted off the stove. I used the pliers to pull the wires from the old burner, then placed them onto the contacts on the new burner. Set it in place, and gave it a clockwise twist until it was snug. This stove originally came with gaskets beneath the burners, but the info for the replacement part stated that a gasket was not... Read more

Our dryer suddenly began overheating while drying. Outside of the dryer cabinet was uncomfortably warm to the touch, dryer drum was hot, charred smelling laundry. Based on what I read it was likely one of two things - a failed cycling thermostat or a shorted heating element. First I cleaned the vent hose and ducting to ensure good airflow, which I had. I opened the circuit breaker first, then took off the door and front cover. I started with a thorough cleaning of the dryer with a vaccuum... Read more

Replaced with thrust bearing kit. Watched your video and it took about 10 minutes to fix. Thanks Read more

There was a horrible screeching noise coming from the washer, and upon inspection I found that the retaining nut that attaches the cam to the machine was either improperly tightened to begin with or had worked itself loose causing the cam to wobble and the belt to work down the cam. The cam gear teeth became worn and the belt worked itself half off the cam and cut a hole in the protective plastic screen containing the whole ensemble. I purchased the belt, shield and cam kit. The parts are... Read more

• Door sweating

Removed old gasket. Replaced old gasket with new. A small wooden block helped seat gasket. Read more

• Will not fill with water
• No hot or cold water
• Will not stop filling with water

I called Appliance pros and asked for a diagnosis. They gave one and sent me the part. It took 15 min. and it worked perfectly. Also got super fast delivery on the part. Thank you!! Read more

• Element will not heat

Replace burner and receptacle. The product arrived promptly after order and the receptacle came in a factory Whirlpool bag, indicating it was a genuine Whirlpool part. The burner did not have such identification, but works very good. I've placed 3 orders with these folks for various broken appliances, and each one has worked as advertised and performs like new. Read more

My husband replaced the broken parts with the new ones that we ordered from you. They fit perfectly! Read more

I pulled the dryer away from the wall and unplugged it. Then I used a 5/16 nut driver and removed the 2 screws in the bottom front panel and pulled it off. Next I removed the 2 5/16 screws holding the front door panel and pulled it down far enough to disconnect the wires for the light and the wires on the door switch. Then , using a putty knife I popped the springs holding the top and control panel then pulling the top up and resting it against the wall. Now I started my repair by laying on... Read more

I replaced drum rollers, axle shafts and front bearing kit. Still had noise. Ordered Idler Arm, Belt Tension Pulley & Washers. I ordered parts at 3:30 pm on a Wednesday, received new parts at 11:30 am Thursday. The instructions & videos were very simple to follow and provided excellent tips. Back up and running with silence in an 1/2 hour. My 13 year old dryer is running like new again. Way cheaper than calling a repairman. Read more

I watched the video at your website. I unplugged the electric first. When I opened up the machine up, It was loaded with lint.I found the source was a hole in the vent tube outside the machine. I fixed that first . The lint had been sucked back into the machine. The first half hour was spent vacuuming out all the lint and then I could proceeded with the motor change. I followed the video exactly. I removed the screws at the two front corners, after lifting the top and controls and tying it... Read more

• Won't start
• Door latch failure

Discovered that the common cause of the problem was the latch in the door. Found a video online that showed the exact procedure for my model dishwasher. Ordered the part from AppliancePartsPros on a Thursday afternoon and it was in my hands by noon on Friday. Carefully took the door apart, compared parts, reassembled, and the joy on my wife's face was priceless when the dishwasher started up without doing anything special. Do not be afraid to attempt this repair. Read more

Replaced clutch assembly, gearcase input shaft seal and motor coupler. When I disassembled the washer I realized the shaft seal on the top of the gearcase was leaking and not the input shaft seal. So had to order more parts before I could finish this job. Altogether I replaced agitator dogs, both seals on the gearcase, the clutch assembly and the motor coupler. Agitator dogs replacement is a very easy job, no tools required, takes less that 5 minutes and made a huge difference with how well... Read more

Water dispenser came down to a trickle and made a lot of noise, I changed the filter but it didnt help and thus the water tank/head assembly needed to be replaced. Replacing the water Tank/head assembly was an easy task, the hardest part is removing the covers and taking care of not breaking the insulation of the water inlet hose. For the not-so-experts like me it is also good to rememebr to have a bucket to collect all the water that comes out after the connection to the solenoid valves is... Read more

• Doesn't shut off
• Won't start

It's working now Read more