Need Help?
Call
Plastic drum baffle that lifts and tumbles clothes during drying. Replace if cracked, broken, detached, or missing from inside your dryer drum.
I installed it my self by watching your video Read more
Attaches to the timer shaft to select wash cycles and start your washer. Replace this knob if it's cracked, stripped, broken, or missing to restore control.
I diagnosed the problem, identified faulty parts, and replaced those components. Read more
Extends your washer's drain hose to reach distant standpipes or sinks. Includes coupler and clamps. Replace when you need extra length for installation.
Attached drain hose extension and it more than reached the drain. Read more
Secures the agitator to the drive shaft in top-load washers. Replace this collar if it's cracked, worn, or missing to restore proper agitator alignment.
I bought the $6.00 plastic clip that holds the agitator In place while washing and the $10.50 spanner wrench that takes the 2 top nuts off to get to the agitator stem the other tools necessary for the job which are just a couple of things I already had then watched the video on line of how to do the job and then did it the whole thing took about 2 hours plus I took my time and gave both tubs a very good cleaning. I paid a guy $400.00 9 months earlier to do the same job wish I hadn't, should... Read more
Upper agitator not turning or engaging? This washer clothes mover works with cam and dogs to roll laundry. DIY repair in 15-30 minutes with video guide.
I ordered all parts of the agitator top, matchup was exactly the same and replaced them quickly. Read more
Fix loud rattling or thumping noises in your dryer with a new blower wheel. Common repair when the fan hub breaks or spins freely on the motor shaft.
Blower wheel and clamp replacement. Initially, we replaced both the belt and drum roller wheels but that did not stop the noise. By reviewing videos on YouTube and AppliancePartsPros, we suspected that the blower wheel could be problematic, even though with front panel of dryer off, we did not see any visual clues to support that theory. Purchased the replacement clamp as well, just for good measure (and it was inexpensive). Note: we did call AppliancePartsPros with our model AND serial numbers... Read more
Replaces worn or broken refrigerator door closer cam that installs at the bottom hinge. Restores smooth door action when the original is cracked or damaged.
Watched the video at Appliance Parts Pros. Followed the video. I was fixing the refrigerator door (a little easier then the freezer door). The repair was very simple and took less then 15 minutes. Read more
This door seal replaces a worn or damaged gasket around the oven door, creating a tight barrier between the door and the front frame. A fresh seal helps the appliance heat efficiently and maintain steady cooking temperatures. What it does:
Found the right part at AppliancePartsPros.com, ordered the part, watched the tutorial. Took less than 5 minutes to install new door seal, and now our laundry area is no longer hot and humid. Before we changed the seal, warm air was leaking around the door and made the laundry room and the kitchen next to it unpleasant. Thanks for the great door seal and the handy tutorial! Read more
This is the central wash-action component in select top-load washers. Replacing a worn or damaged agitator restores proper agitation so clothes circulate through water and detergent for consistent cleaning performance. What it does:
I have a 25 year old Kenmore washer that works well and didn't want to get a new washer as they don't make them like they used to. Upon removing the top cap of the agitator and doing an inspection, the agitator dogs were completely broken into pieces. Due to age we decided to replace the lower and upper agitator along with the agitator auger dogs repair kit. All new parts and works fine. On inspection of old parts, we probably could have gotten away with just a $5 repair for the plastic... Read more
Replace a broken or fatigued oven door spring to restore proper counterbalance. Installs behind side panel. Ensures door closes firmly and seals correctly.
It was a simple fix. I removed the six screws holding the side panel on the range. Removed the broken parks of the spring. I use a screwdriver to help stretch the new spring into place. I then replaced the side panel and screwed it on. About ten minutes work. Read more
Replaces cracked, stained, or warped oven bottom panel in gas ranges. Covers burner assembly and provides smooth, cleanable floor surface. Easy install.
I ordered the new oven bottom from Appliance Parts Pros and within three days I had a brand new oven bottom. Took the old one out, the new one fit superbly. The next time I will definitely put foil or an oven liner on the bottom rack to catch the drips from the pies as the Aqua-lift cleaning system on the Whirlpool oven did not do the job. Read more
Fix erratic or unresponsive cycle selections with this laundry center rotary encoder switch. Mounts behind the cycle knob to restore accurate settings.
Replaced with a new one. Read more
Auxiliary burner head for gas ranges and cooktops. Mounts over the orifice to distribute gas through precision ports. Replace if clogged or damaged.
Oven won't turn off or stays on low heat? This temperature-sensing thermostat regulates oven heat and prevents overheating. Moderate DIY repair.
I replaced the thermostat and its control switch as it was not able to turn off. Read more
Oven won't heat or overheats? This thermostat monitors temperature and controls heating elements. Moderate DIY repair requires back panel removal.
Removed back panel and top burner cover to replace thermostat Read more
This contact spade is a push-on electrical terminal used to connect an appliance wire lead to a component's blade. Replacing a worn or heat-damaged connector restores a secure fit and consistent power flow.
Full disassembly of removable tray into top plate (stainless) and lower pan taking care not to loose fasteners. Removal of terminal blocks using lubrication on rusted screws and, if necessary, drill out technique. Unclip wires from edges of the tray on both sides without losing the clips for future re-use. Top plate is now completely free of connections and may be cleaned/scrubbed separately in advance of re-assembly. Unfasten spade insulation block (located in the front of the tray) after... Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.