Admiral Parts

• Won't start

I removed the belt and found with no load the motor ran but made a grinding noise. I purchased a new motor and installed it. The fix was easy and quick. Read more

This was the second attempt at fixing this problem. The first repair and parts were generated by listing the problem and reviewing the potential corrections, listed on the web site. From making repairs on other clothes washers, I was confident that some of those potential causes could have been the cause. Unfortunately the counterbalance spring and suspension springs were not the cause as they were attached as intended and in good condition. I reached out for Appliance Parts Pros input... Read more

• Too hot
• Shuts off too soon

I posted the following on the Facebook page ; SOoooo my 10 year old clothes dryer stopped and like almost everyone else I just figured it's shot, burned up, gotta get a new one. Well, due to a few bumps in the road I cannot afford another problem. My 2 vehicles are not running and with one being in the shop for 3 weeks and not being able to afford a rental car anymore this dryer was another headache. It sat for weeks and laundry started piling up. While looking online for sales somehow I... Read more

• Will not agitate
• Pumps but will not spin

I had previously replaced the pump about 1 year ago. That was not the problem. Still leaked the same way - intermittently, but always in the center of the washer onto the floor. None of the hoses were leaking - no evidence of corrosion or water mineral residue at any of the hose fittings. So, it must have been something else. I studied the parts diagram for the washer tub assembly and concluded the source of the leak almost had to be the outer tub's Centerpost Gasket. It was really the... Read more

The ridges inside the agitator base were stripped. Installed a new base - after a good cleaning of build-up on the spindle. Works like new! Read more

18 year old Maytag Atlantis top load washer had a load knocking and rattle sound with excessive vibration when the tub was spinning, but not when it was agitating. They was no water leaking. I took the front panel off and carefully listened while I ran a cycle and the loud sound sounded like it was coming from the drain pump. So I took off the drive belt and noticed that it was glazed and that there was belt material on the drain pump and tub transmission pulleys. I removed the drain pump and... Read more

Unplugged unit from power. Removed two sheet metal screws and lower front panel, removed two sheet metal screws and door panel (disconnected three door switch wires and two light wires - noted the connected position of each wire ); removed three self-tapping screws and black plastic hot air outlet to fan duct from lower end of front bulkhead; removed sheet metal screws and front bulkhead; removed two sheet metal screws from dryer top panel and raised top up and back on rear hinge brackets;... Read more

As a Mechanic, I did the common sense approach: INITIAL OBSERVATIONS & CHECKS: - Unplug Machine & check inlet water hose connections for leaks and signs of hose failure; - Remove back panel & inspect for water presence at all hose connections, pump, bottom of basket (bottom center of basket where the main motor, shaft bearing, and tub seal is located), dispensers, bottom of wash basket, water injector area, look everywhere where there is a hose connection and where water flows... - Inspect... Read more

First, I watched your VERY HELPFUL videos showing exactly how to remove and assemble the parts. I removed the salvageable parts from the old shelf frame and reassembled it. Read more

Replaced water inlet valve took all of 10 minutes and washer is filling great on hot and cold. Thanks to Appliance Parts Pros for getting me the part within 24 hours. I have a very happy customer. Read more

• Won't start
• Fridge too warm
• Freezer section too warm

Replaced capacitor and starting relay on the compressor in 15 minutes. The problem may have just been the capacitor, but rather than trying that and if it didn't solve the problem i would have had wait for the relay. Read more

I purchased the lid latch assembly and the lid switch strike. Following the clear video instructions for each part, my handy teenage son was able to remove the lid latch assembly and replace it with the new part as well as the lid switch strike. The washer is back to working perfectly for under $100. Appliance Parts Pros carry the parts to repair and at a lower cost than other online retailers. I saved about $30 compared to the other online site and I saved a service call fee. I'm so glad I... Read more

• Leaking

After discovering your web site and reading of others issues I ordered a door seal (my old one was a little short on the right side) a detergent door grommet, and the 2 water deflectors ( I decided to cover all the bases while I was at it. Very simple job with the information provided on your web site. I certainly have the confidence to tackle other appliance repair now. Read more

I ordered the replacement part from Appliance Parts Pros. It arrived a few days later. A helpful video on YouTube showed me how to do it. The baffle was replaced in approx. 1/2 hour. Thank you AppliancePartsPros for you courteous help and speedy delivery. I will return when in need. Read more

• Too hot
• No heat or not enough heat
• Shuts off too soon
• Takes too long to dry

This Maytag dryer was bought in 1985 if memory serves. It has worked hard with few repairs done by yours truly over the years. Thanks to the engineering and excellent design by Maytag staff, removing parts are relatively easy. Once I opened the unit, I found it to be full of lint. I cleaned the entire inside and the vent pipe duct work. I found the blower wheel assembly worn. Though it was not cause of my problem, I decided to change it along with the igniter, heater relay and the fan belt. I... Read more

Bought new Transmission/gear box. Putting in the new one was easy. Taking the old one out was a nightmare. The corrosion on the spanner nut and drive block was awful. Ten years of VERY hard water and six kids made for a lot of corrosion and hard water crystallization. I do not own a spanner wrench. I am not sure having one would've helped. I tried pipe wrenches, needle nose vice-grips and many other ways. What eventually worked was taking a three inch ratchet extension, putting it... Read more