Blade

21.23-inch mulching blade for 42-inch deck lawn tractors. Replace when blade edge is worn, bent, or cracked. Features 6-point star center hole.

Replace your cracked, bent, or dull mulching blade. This precision blade installs on the mower deck to finely cut grass clippings for lawn mulching.

Connects mower blade to spindle for secure attachment. Replace if stripped, cracked, or worn to ensure blade stays properly mounted during operation.

These quality tiller tines are used on a variety of yard tillers. Tiller tines are blades attached to the tiller that turn soil and prep it for cultivating a garden. As the tiller tines are used, they can become worn down, broken, or damaged through use or impact with rocks and other debris. These are C-shaped tines that can cut through dense soil.If the tiller tines are bent, dull, or damaged, they will need to be replaced, otherwise they might till the soil unevenly and may not reach the depth required. To replace the tines, remove the spark plug wire before taking off the tine shield end cover. Taking out the tines requires removing the cotter pin from the clevis pin so the clevis pin can be pulled out. Next, the tines can be pulled directly off of the shaft. Slide on the new tines and reinstall the clevis and cotter pins before using the tiller again.These tiller tines are an authentic OEM replacement part directly sourced from the manufacturer. It is sold as an individual part. The tines are compatible with tillers manufactured by MasterCut, Craftsman, Yard-Man, Cub Cadet, Bolens, Yard Machines, MTD, Huskee, and Montgomery Wards.

Flail blade for chipper shredders. Replaces worn, chipped, or broken cutting teeth. Essential component for shredding and chipping operation.

Replacement edger blade for cutting grass and weeds along concrete and landscape edges. Replace when blade becomes dull, damaged, or worn from ground contact.

Replacement screen blade for chipper shredders. Controls shred size and protects engine components. Replace if cracked, damaged, or broken from debris impact.

The tri-cut blade works to replace edger blades to ensure they are sharp and capable of cutting through the grass and turf properly. The blade is made from metal and can provide users with clean edging around the edges of their lawn and around flower beds. Regularly examine the edger blade regularly to ensure that it is not bent, broken, or otherwise damaged. If your current edger blade is no longer sharp and cannot be sharpened, it is time for a replacement. Without a sharp blade for the edger, it will be impossible to take care of the lawn properly. To replace the blade in your edger, the only tool required is a wrench. Replacing the blade is easy, and it should not take more than 15 minutes. This OEM part is sold individually, and it works with edgers from a range of brands, including Craftsman, Yard Machines, MTD, Troy-Bilt, Bolens, and Yard-Man.

This genuine MTD shave plate, also known as a scraper bar, can be used as a replacement part for snowblowers. The shave plate is located at the bottom of the auger to scrape snow off of surfaces and filter it into the auger of the snowblower.Damage to the shave plate might include cracks, dents, and erosion to the metal material, or it can gradually wear out and no longer be effective. Evidence of a cracked shave plate can come from a visual inspection, but it can also be detected if the snowblower is doing a poor job of collecting and scraping snow off of surfaces. A cracked shave plate should be removed and replaced immediately, and a snowblower should not be used before the part is replaced. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This shave plate is compatible with the following brands: MTD, Yard Machines, Cub Cadet, Yard Man, and Craftsman. Part sold individually.

The snow thrower shave plate is a metal scraper located at the bottom front of the auger housing that clears snow down to the pavement surface. Replace it when you notice uneven snow clearing, gouging of surfaces, or visible wear and chipping on the plate's edge.

A blade is the part of chippers and shredders that cuts the grass. It spins rapidly and pulls the grass up before cutting it. The grass is sucked into the deck, where the clippings continue to get chopped into smaller pieces before getting expelled. With regular use of the blade, after accidental damage, or because of the age of the machine, the blade may cease to perform adequately. Running the lawn equipment over rocks or other solid obstacles may also cause the blade to break. In any case, the blade has to be removed, and a new blade should be installed. Wear gloves for protection and handle the blade with caution. Make sure the machine is cooled entirely before beginning the repair.This blade is a genuine OEM part sourced directly from the manufacturer. It is made of durable, high-quality metal. The blade is sold as an individual unit. The replacement part is compatible with MTD, Troy-Bilt, Yard Machines, and Huskee brand lawn and garden machines, including chippers and shredders.

Replacement blade for chipper shredders. Installs on the cutting mechanism to chip wood into small pieces. Replace when dull, chipped, or damaged.

Complete 46-inch mulching blade kit for lawn tractors. Includes blades designed to finely chop grass clippings. Replace worn or damaged blades.

This 50-inch blade is made for use with riding lawn mowers by Craftsman and Husqvarna. The blade is the component that is responsible for cutting grass or other foliage when the lawnmower is in use. The blade can become worn over time and will leave grass with frayed edges. If the blade is worn out, it will need to be replaced to create a healthier-looking lawn. Replacing the blade will create a clean cutting edge after regular use of a lawnmower.If the mower blade needs to be replaced, a pair of pliers, a socket set, and a wrench set will be required. Place the lawnmower on a stable surface and pull up the blade deck for better access to the 50-inch blade. Take out the blades and the sheared pins before replacing them with new components. Reassemble the deck and test the lawnmower before use.This is an authentic OEM replacement component that is directly sourced from the manufacturer. It is sold as a single part. The 50-inch blade is made to be used in several lawn mowers and lawn tractors manufactured by Husqvarna and Craftsman.