Cooktop Gas Conv Kit Parts

This LP conversion kit converts a compatible gas appliance from natural gas to propane (LP) so burners operate with the correct orifice sizing and fuel flow. Use when changing fuel type to restore proper flame performance and safety. What it does:

• Replaces orifices and/or components needed to match appliance fuel flow to propane (LP)
• Helps restore proper flame size and color after switching fuel types
• Addresses symptoms such as weak or uneven flames, hard ignition, or yellow/orange flame tips
• Ensures appliance operates as designed on the correct fuel when installed per OEM instructions

• Follow the OEM conversion instructions exactly and keep the original parts; improper conversion can be unsafe.
• Shut off the gas supply and power before starting; check all connections for leaks after installation.
• Some conversions must comply with local codes — verify requirements before proceeding.
• Use only the orifices/components supplied with the kit for the specified appliance; do not modify parts.

This jet holder secures the jet/nozzle assembly, keeping it correctly positioned for consistent flow and performance. Replacing a cracked or loose holder restores proper alignment and helps prevent leaks, drips, or irregular spray from the outlet.

• Holds the jet/nozzle firmly in place to maintain directed flow
• Keeps the jet aligned for even, reliable output
• Helps seal the connection to reduce drips at the fitting
• Typical symptoms: loose or missing jet, visible cracks, leaks, weak or erratic spray

• Disconnect power and shut off the applicable supply to the appliance before servicing
• Access the jet assembly and note the holder's orientation for correct reinstallation
• Inspect any O-rings/seals at this connection and replace if worn or damaged
• Reassemble carefully and avoid overtightening; test for proper flow and no leaks

This gas burner jet holder assembly routes fuel through the orifice to the burner and secures the connection. The red 11,000 BTU version is designated for the right-front or left-rear burner, helping restore proper flame and heat output.

• Positions the jet and routes gas from the manifold to the burner for the specified heat output
• 11,000 BTU, red-coded variant designated for RF/LR burner location
• Provides a stable, serviceable connection between tubing and burner base for a consistent flame
• Symptoms include weak or irregular flame, failure to ignite, or incorrect flame size at the RF/LR burner

• Shut off gas supply and power; allow the appliance to cool before servicing
• Remove grates, burner caps/heads, and any panels needed to access the holder
• Support gas tubing and use two wrenches on fittings to avoid twisting or damage during removal/installation
• After installation, check all joints with an approved leak-detecting solution and verify flame quality

This conversion kit provides the orifices and instructions needed to convert a compatible gas range/oven from natural gas to liquid propane, restoring proper fuel flow and safe burner operation after a fuel-type change. What it does:

• Replaces factory natural-gas orifices with LP orifices sized for propane fuel
• Helps restore correct flame height and even heating when switching to LP
• Addresses weak or irregular flames that occur after changing fuel types
• Ensures burners receive the proper fuel jetting for safe LP operation

• Installation should follow OEM instructions exactly
• Turn off gas supply and electrical power before beginning work
• Use proper leak testing after installation and before returning the appliance to service
• Regulator adjustment or replacement may be required per OEM service instructions

This jet holder assembly secures the burner orifice and delivers the correct-sized gas jet for a 12,500 BTU natural gas burner, helping restore proper flame size and consistent ignition. What it does:

• Holds the burner orifice in the correct position so gas flows through the proper jet
• Provides the factory-sized orifice for a 12,500 BTU natural gas burner to maintain intended flame height
• Helps correct weak or uneven flames caused by a missing, damaged, or incorrect jet holder
• Supports reliable ignition when installed and aligned properly

• One jet holder assembly (blue) with the 12,500 BTU natural gas orifice installed

• Turn off the appliance and shut off the gas supply before starting any work
• Only install the exact orifice variant specified for your appliance; confirm color/marking and orientation before tightening
• Re-check all gas fittings and perform a leak test after installation

This LP orifice kit supplies four factory-style liquid propane burner orifices to convert the cooktop burners for use with LP gas, restoring proper fuel flow for reliable ignition and consistent flames. What it does:

• Replaces LP burner orifices to set correct fuel jet size for propane
• Helps correct weak, uneven, or hard-to-light burner flames after conversion
• Restores consistent burner performance and heat output when properly installed
• Matches OEM fit and flow characteristics for compatible cooktops

• Four (4) LP burner orifices as shown

• Follow the appliance conversion instructions and local codes; conversion often requires replacing orifices and adjusting orificing settings
• Turn off the gas supply and electrical power before starting work
• Use proper tools; do not enlarge or modify orifices

Right rear

Left front

The range conversion kit is an OEM component specifically designed for Whirlpool ranges. This kit contains all the necessary parts to convert a range from natural gas to propane gas or vice versa. 

Symptoms of an incompatible or incorrectly installed conversion kit include:

• Incomplete or unstable burning of the gas 
• Yellow burner flame tips instead of blue
• Higher than normal gas usage
• Issues with ignition or flammability 

Causes of a bad conversion kit could be improper installation, damaged or missing components, or using a kit not designed for the specific range model.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Natural gas

Natural gas. Simmer burner

This orifice holder secures the 17K gas orifice in the burner assembly so the correct orifice stays aligned for reliable burner performance. Replaces a worn or damaged holder to restore proper gas flow location. What it does:

• Holds the 17K burner orifice in the correct position inside the burner/head assembly
• Keeps the orifice aligned so the burner lights and flames remain stable
• Helps prevent orifice movement that can cause uneven flames or ignition issues
• Fits in the valve/burner mounting area to maintain safe gas discharge alignment

• One orifice holder

• Turn off gas supply and power to the appliance before attempting any service
• Replace only with the exact part; ensure orifice is seated correctly and fasteners are secure
• Check surrounding burners and gaskets for damage while servicing

Natural gas

This conversion orifice spud kit contains three precision orifice spuds used to change the gas flow profile for compatible cooktop/oven burners. It helps restore correct burner flame size and performance after a fuel-type conversion. What it does:

• Replaces worn or incorrect orifice spuds to set proper gas flow for burner operation
• Used in fuel-type conversion to match burner jets to the correct gas pressure/type
• Can resolve uneven or weak flames and burners that won't reach expected heat
• Works with each burner where a standard orifice spud is specified

• Turn off gas supply and disconnect power before servicing; follow all safety procedures
• Installation may require burner removal and a proper wrench or driver for the spuds
• After installation, check all fittings for leaks using a gas leak detector or soapy water

This orifice holder assembly secures the gas orifice and directs burner gas flow for safe, consistent ignition and flame control. It replaces a worn or damaged holder to restore reliable burner operation. What it does

• Holds the gas orifice in the correct position on the burner tube for proper fuel delivery
• Directs gas flow to the burner for consistent ignition and steady flame
• Helps prevent gas leaks or misalignment from a loose or damaged holder
• Commonly needed when burners fail to light evenly, flame is unstable, or parts are visibly cracked/corroded

• One orifice holder assembly

• High-level replacement; disconnect gas supply and power before starting
• Use proper sealing and torque on fittings; check for leaks with a safe leak-test method after installation
• Verify correct part number and fit for your specific appliance before ordering

18K