Cooktop Gas Conv Kit Parts

The Gas Range LP Conversion Kit is an OEM part for specific Whirlpool gas ranges. It allows built-in ranges fueled by natural gas to be safely converted for use with liquid propane (LP) fuel. 

Symptoms requiring an LP conversion would include: 

• Inability to ignite or achieve proper combustion using natural gas 
• Unstable burner flame patterns or inconsistent heat output
• Gas leaks or improper connection to an LP fuel supply

Causes for needing an LP conversion kit include choosing to install the range in an area only serviced by LP gas, rather than natural gas. Additional causes could be wear and failure of the original equipment over time.  

This OEM kit is compatible with select Maytag, KitchenAid, Jenn-Air, and Kenmore gas ranges.

Liquid propane

This replacement tube restores a damaged or missing refrigerator tubing connection so the appliance can route fluids where intended and operate reliably. It's a direct-fit service part for the matching OEM assembly. What it does

• Provides a sealed conduit for fluid flow inside the refrigerator
• Re-establishes a proper connection when the original tube is cracked or broken
• Helps stop leaks or pooling caused by a damaged line
• Supports normal operation of the associated water/defrost subsystem

• One replacement tube as shown

• Only install when the appliance is powered off and disconnected from its water supply if applicable
• Inspect adjoining fittings and replace any worn clamps or seals to ensure a leak-free connection
• Use appropriate tools; avoid sharp bends that can kink or restrict the tube

A single gas burner orifice that meters fuel flow to a range or oven burner for consistent flame sizing and reliable cooking performance. Replaces a worn or clogged orifice to help restore steady ignition and even heat. What it does:

• Controls the amount of gas delivered to a burner for proper flame height and heat output
• Helps maintain consistent cooking and baking temperatures when functioning correctly
• A clogged or damaged orifice can cause weak or uneven flames, slow ignition, or poor heating
• Works as a small, precision-fit insert that sits in the burner assembly

• Turn off the appliance and shut off the gas supply before servicing
• Use a wrench or socket sized to the orifice and avoid rounding the fitting
• Inspect burner ports and clean any debris before installing the new orifice

This LP conversion kit converts a compatible natural-gas range or cooktop to run on liquid propane, restoring correct fuel flow and burner performance for homes using bottled propane. It provides the parts needed for proper gas type change. What it does:

• Replaces or adjusts burner fuel delivery so the appliance operates safely on liquid propane
• Restores correct flame characteristics and heat output after conversion
• Helps resolve symptoms like burners that burn poorly, produce yellow or sooty flames, or have reduced heat on the wrong gas type
• Supports safe operation by allowing proper jet/orifice sizing and regulator settings for LP

• Conversion kit components required to convert a natural-gas range or cooktop to liquid propane

• Conversion must follow the appliance's OEM instructions exactly; keep the manufacturer's supplied procedure and torque/adjustment notes
• Require basic tools; some kits need orifice removal/installation and regulator adjustment
• Shut off gas supply and disconnect power before starting work; check for leaks after conversion using a soap solution

Natural gas. Main burner.

This orifice spud directs gas flow into the burner for consistent ignition and flame control. It restores proper burner performance so cooking heats evenly and burners light reliably. What it does:

• Seats the burner orifice to control gas flow to the burner
• Helps maintain a steady, even flame for consistent cooking
• Can resolve weak or uneven flames and burners that struggle to light
• Works as the sealed interface between the gas manifold and burner tube

• One orifice spud

• Turn off the gas supply and disconnect power before servicing
• Inspect surrounding seals and gaskets for damage and replace if necessary
• Use basic hand tools; avoid overtightening to prevent damage

This orifice spud directs gas flow to a burner for correct flame performance, restoring safe, consistent ignition and heat. It's a direct-replacement component used where the factory orifice has become damaged or worn. What it does:

• Controls the gas flow to a specific burner for proper flame size and combustion
• Helps restore consistent ignition and even heating when a burner burns low or unevenly
• Can stop symptoms like weak or unstable flames and uneven cooking
• Does not alter appliance settings—matches OEM flow characteristics when installed

• Turn off the gas supply and power to the appliance before starting any work
• Use appropriate tools and thread sealant rated for gas joints if required by the manufacturer
• After installation, check all connections for leaks with a soap solution or approved leak detector
• Gas-system repairs are safety-sensitive; perform the replacement

Natural gas. LG 1.68mm

This orifice spud is the small gas jet used in LP conversion kits to regulate propane flow to a burner, helping restore correct flame size and combustion after converting to liquid propane. It's a direct-fit component for affected burners. What it does:

• Replaces the burner jet that meters propane for safe, consistent flame
• Restores proper flame height and prevents oversized or sooting flames after LP conversion
• Helps burners light reliably and maintain even heat
• Works as part of an approved LP conversion to match appliance fuel type

• Turn off gas supply and power before starting any gas appliance service
• Use the correct orifice size and follow the appliance LP conversion instructions or service manual
• Hand-tighten and then torque per manufacturer spec if provided; avoid overtightening

The Holder Orifice is an OEM component specifically designed for Whirlpool ranges. Located inside the gas burner unit, the orifice holds the brass valve that regulates gas flow to each burner flame. Its sturdy construction and precisely sized opening ensure a stable, controlled fuel supply.  

Causes of a bad holder orifice can include mineral deposits building over time which diminish sizing accuracy or cracks developing that cause leaks.

Symptoms of a bad holder orifice include:  

• Burners emitting unstable or sporadic flames of abnormal sizes
• Inability to efficiently ignite or achieve proper burner settings  
• Strong gas or fuel smells coming from the range top
• Discolored or corroded brass components

This OEM Whirlpool part is also compatible with KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore cooking appliances. 

This air shutter controls the air-to-gas mixture for a range/oven burner to help produce a proper flame for efficient cooking and reliable ignition. It's a simple replacement part that restores correct airflow at the burner inlet. What it does:

• Regulates burner airflow to help achieve a stable, properly-colored flame
• Helps correct weak, uneven, or yellow-tipped flames when misaligned or damaged
• Supports consistent ignition and steady burner performance
• Works at the burner/orifice connection to fine-tune combustion air

• Turn off gas supply and electrical power to the appliance before servicing
• Remove burner components as needed to access and replace the shutter; retain screws or clips
• Position the shutter per OEM orientation and secure; do not overtighten fasteners

This orifice hood directs and stabilizes the natural gas flow to a single range/oven burner for reliable combustion and consistent heat. It helps restore proper burner performance when the hood is damaged or worn. What it does:

• Guides natural gas from the orifice to the burner for steady flame and efficient combustion
• Commonly used when burners have weak, uneven, or unstable flames
• Can resolve ignition problems tied to damaged or misshapen hoods
• Supports correct flame shape to reduce yellow tipping or sooting

• Turn off gas supply and electrical power before servicing; follow local codes
• Install on the burner tube/orifice assembly as shown in your service manual
• Inspect surrounding fittings and gaskets; replace any damaged components
• After installation, check for gas leaks and proper burner operation