Cooktop Heating Element

The Surface Element is an OEM part for Bosch cooktop and ranges. Measuring 6 inches across, it provides focused heat from below for smaller sized cookware.

Causes of a bad 6" plug-in element generally relate to normal wear and tear over time. Spills left on the coils could potentially cause issues by corroding internal wiring or damaging heating components.

Symptoms of a bad narrow surface element can include:

• The element heating intermittently or not at all
• Only parts of the coil visibly heating up
• Buzzing or clicking coming from below the element
• Tripped circuit breakers affecting that specific element

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Broil element not heating? This upper heating element restores high-heat broiling and even browning. Straightforward DIY fix takes under 30 minutes.

Broken element not heating? This radiant bridge connector restores electrical contact between your cooktop element and wiring. Takes 10-15 minutes to install.

Burner not heating or heating unevenly? This 6-inch surface coil element restores consistent heat to your electric range. Simple plug-in replacement.

Burner won't heat or stuck on high? This surface element restores proper heating control to your electric range stovetop. Common DIY repair.

This 20-inch bake element heats the bottom of the oven cavity so food cooks and browns evenly. Replacing a failed element restores proper oven heating and baking performance. What it does

• Heats the oven's bake chamber during bake cycles
• Replaces a cracked, burned-through, or non-heating bake element
• Helps resolve symptoms like no heat from the bottom, uneven baking, or oven failing to reach set temperature
• Works with the oven's control and safety circuits to provide consistent heat

• Disconnect power to the appliance at the breaker or unplug before starting
• Access usually requires removing the oven cavity bottom or back panel
• Handle the element by its insulated areas and avoid bending or touching the bare heating surface
• Tighten terminal connections securely and verify operation with the oven empty after reassembly

The Surface Element (240V-2100W) is an OEM part for Bosch cooktops and ranges. It provides consistent, even heating from below pans on the cooktop surface.

Causes of a bad surface element can include normal wear and damage from extended, heavy usage. Food or liquid spills left on the element for prolonged periods could potentially corrode the coils or electronics over time as well.

Symptoms of a bad surface element include:

• Element not heating up at all or heating unevenly
• Element heating intermittently or stopping prematurely
• Buzzing, clicking or smoke coming from below the element
• Tripped or blown circuit breakers when using that element

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Burner not heating or won't turn on? This 12-inch halogen element restores radiant heat to your cooktop. Common DIY repair with basic tools in 30 minutes.

If your cooktop burner won't heat or stays on high, this surface heating element may need replacement. Moderate DIY repair with basic tools.

Broiler not heating or browning food properly? This upper oven broil element restores high-heat broiling for searing and finishing. Easy DIY fix.

This oven bake element heats the oven cavity so food cooks and bakes properly. Replacing a worn or broken element restores consistent heat for even baking and broiling. What it does:

• Converts electrical power into heat to warm the oven interior during bake and broil cycles
• Replaces a damaged or open element that can cause the oven to not reach temperature or cook unevenly
• Works with the oven's control system to provide steady, distributed heating
• Common symptom: oven won't heat, heats very slowly, or produces uneven cooking results

• Disconnect power at the breaker before starting any repair
• Allow the oven to fully cool and wear gloves to protect against sharp edges
• Remove the oven bottom or access panel as required, disconnect element wiring, and secure the replacement element in the original mounting
• Reconnect power and perform a short test bake to ensure proper operation

This bake element is the oven's primary heating element for baking and roasting, restoring proper oven heat so food cooks evenly. It replaces a damaged or worn element to bring back reliable bake performance. What it does

• Heats the oven cavity during bake cycles to provide consistent cooking temperatures.
• Commonly linked to symptoms like an oven that won't heat, takes too long to preheat, or produces unevenly cooked food.
• Visible damage (breaks, blisters, or heavy corrosion) or open electrical continuity are signs this element needs replacement.
• Works with the oven's control and safety systems to cycle heat as required.

• One bake element

• Disconnect power at the breaker or unplug the appliance before starting any work.
• Allow the oven to cool completely and handle the element carefully to avoid sharp edges.
• Inspect wiring and terminal connections; replace any damaged connectors before reassembly.
• After installation, restore power and run a short bake cycle to ensure proper operation.

This bake element heats the oven's lower chamber so food and bake cycles reach cooking temperatures. Replace a damaged or non-heating element to restore even baking and proper oven operation. What it does

• Converts electrical power into heat for the oven's bake cycle.
• Heats the oven's lower cavity to maintain set cooking temperatures.
• Commonly replaced for symptoms like no heat, weak heat, or uneven baking.
• Works with the oven's controls and sensors to deliver consistent bake performance.

• Disconnect power to the range at the breaker before starting any work.
• Allow the oven to cool completely and wear gloves to protect against sharp edges.
• Remove the oven racks and detach mounting screws and wire connectors to replace the element.
• Only reconnect power after the element is secured and wiring is reattached; test on a short bake cycle.

This heater assembly replaces the dryer's heating unit to restore normal drying performance and consistent drum temperatures. It's a direct-fit replacement designed to match the OEM heater layout and electrical connections. What it does:

• Reheats incoming air so the dryer can remove moisture from clothes.
• Works with the dryer's blower and thermostat to maintain operating temperature.
• Commonly used when the dryer produces little or no heat, or runs long cycles.
• Helps resolve intermittent heating caused by a failed heating element or broken heater housing.

• Disconnect power (unplug or shut off breaker) before starting any repair.
• Access requires removing the dryer cabinet or rear panel; follow OEM disassembly steps.
• Inspect related parts (thermal fuse, high-limit thermostat, wiring, connectors) for damage while replacing the heater.

This replacement grill (broil) heating element restores high, direct heat for broiling and browning in the oven. It lets you crisp and brown food quickly so broil functions work like new. What it does:

• Provides the intense direct heat required for broiling and grilling
• Replaces a burnt-out or broken upper oven element to restore broil performance
• Helps eliminate problems like food not browning or uneven broiling
• Visible breaks, blisters, or open circuits on the element are common failure signs

• Disconnect power to the appliance before starting any repair to avoid shock
• Handle element carefully to avoid bending or damaging the terminals
• Reconnect wiring securely