Craftsman Carburetor

The carburetor is the part of the chainsaw that mixes air from the intake valve system and gas before the fuel mixture goes to the engine. This ensures that the chainsaw is capable of continuing to run while it is in use. A bad carburetor will cause problems with how the chainsaw runs, and it may stop running during work. If the engine does not start when the tank is full of fresh fuel, test the carburetor. Start by removing the air filter and pouring a teaspoon of fuel onto the carburetor. Then, pull the starter rope to start the engine. If the engine starts but quickly dies, it means that the carburetor will likely need to be replaced. The replacement of the new carburetor is fairly simple. Remove the rear cover on the chainsaw to remove the old carburetor. Once you have removed the old carburetor, you can then install the new carburetor. Replace the cover and test the chainsaw. This is an OEM sourced part that will work with several models of chainsaws from Poulan and Craftsman.

This replacement carburetor kit is a genuine OEM parts kit for Craftsman hedge trimmers. The carburetor takes gasoline from the fuel line and mixes it with air from the intake valve to make a balanced fuel that is ready for combustion. Depending on how much fuel or air pass into the carburetor, the engine may run faster or slower. The most common reason for a carburetor to break down is if it is clogged with engine gunk. While it is sometimes possible to clean out a carburetor, if left for too long, the damage can be irreparable and the part will need replacing. First, remove the air filter and filter housing using a socket wrench. This will give access to the damaged carburetor and make it easier to unhook from the links that hold it in place. Be sure to set the gaskets firmly in place and then reassemble with the new part. This replacement carburetor is designed for use only with Craftsman appliances. It comes sourced directly from the original manufacturer and includes a carburetor and two gaskets.

Replacement carburetor for gas chainsaws. Mounts to engine block to mix air and fuel. Replace if cracked, leaking, corroded, or missing parts prevent starting.

This carburetor assembly can be used as a replacement part for the small engine of a string trimmer, a chainsaw, or an edger. The carburetor assembly contains a replacement carburetor and the components required to facilitate the replacement and installation of the carburetor. The purpose of the carburetor is to create a mixture of the fuel and air that the engine takes in and channel it through the network of valves to the spark plugs, which ignite and power up the engine.A carburetor might have to be replaced if it is damaged to the point of exhibiting the following symptoms, among others: black smoke pluming from the exhaust, reduced fuel economy, misfires and false starts of the engine, and oil leakages stemming directly from the carburetor. If this is the case, this carburetor assembly should be ordered as a replacement. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer, MTD. It is sold individually. This carburetor assembly is compatible with the following brands: MTD, Troy-Bilt, Ryobi, and Yard Man.

Carburetor assembly for snow thrower engines. Installs on the engine block to mix air and fuel. Replace if cracked, damaged, or leaking fuel.

Genuine carburetor assembly for lawn and garden engines. Creates proper fuel-air mixture for combustion. Replace if cracked, leaking, or damaged.

Carburetor repair kit for trimmers and brush cutters. Restores proper fuel-air mixing when original carburetor components are worn or damaged. 150 chars

Replaces cracked or worn primer bulb that covers the carburetor primer base. Installs on gas leaf blowers and line trimmers to pump fuel for starting.

Carburetor repair kit for gas line trimmers and outdoor power equipment. Includes all parts to rebuild worn or damaged carburetors. Use when rebuild needed.

Carburetor for gas leaf blowers. Mixes air and fuel for engine operation. Replace if cracked, leaking, or damaged to restore proper fuel delivery.

Engine won't start or runs rough? A faulty choke lever prevents proper cold starts. This replacement lever restores choke control for reliable starting.

Carburetor assembly for engine-powered outdoor equipment. Replaces cracked, clogged, or damaged carburetors. Installs on engine to regulate fuel mixture.

This carburetor repair kit is a genuine OEM replacement part for a wide variety of tiller and chipper engines. The carburetor is one of the most essential parts of an engine. It is responsible for mixing a balance of oxygen and fuel for combustion. If the carburetor is damaged, the engine will not produce the right about of combustion and may not start. This kit is for service the carburetor if it becomes damaged. This kit contains a valve needle, jet nozzles, a float and float pin, o-rings and gaskets, and fuel drain plug—everything needed to fix a carburetor. To make repairs to the carburetor, you will need a set of screwdrivers and socket wrenches. The repair will depend largely on what appliance you are fixing, so be sure to follow the instructions in the user's manual. Before making any repair, be sure to allow the engine to cool completely and drain it of excess fuel. This part is designed for tiller and chipper engines made by Cub Cadet, MTD, Troy-Bilt, and Yard Machines. This part is sourced direct from its original manufacturer and ships individually.

Carburetor rebuild kit for snow thrower engines. Includes gaskets and components to restore carburetor function when worn, damaged, or leaking fuel.

Replace the primer bulb on your gas chainsaw to restore proper fuel priming. This small rubber bulb pumps fuel into the carburetor for engine starting.