Craftsman Parts

This blade adapter has a 25mm inner diameter and fits onto the blade of a variety of lawnmowers. The blade adapter allows the blade to connect to the spindle for proper performance. This blade adapter is made of metal. Regular wear and tear can cause the blade adapter to go bad or even split in half. When this happens, the blade adapter will need to be replaced.Before replacing the blade adapter, the lawnmower should be turned off and the spark plug wire needs to be disconnected. Turn the mower upside down to get access to the component. Use a socket set to remove the old blade adapter and replace it with the new component. Replace any other components, connect the spark plug wire, and test the machine before use. This component is sold on an individual basis. It is an authentic OEM replacement part that is directly sourced from the manufacturer. The blade adapter is made to be used with lawnmowers manufactured by MasterCut, Craftsman, Yard-Man, Cub Cadet, MTD, Troy-Bilt, and Yard Machines.

This upper handle can be used as a replacement part for a lawnmower or snowblower. The upper handle allows the user to control the movement of the equipment while it is in operation.If the part suffers damage from direct impact or wears down from use over time, it may need to be replaced. An upper handle can suffer damage in the form of piercing, cracks, scrapes, punctures, and corrosion of the metal material. If this damage makes steering the lawnmower or snowblower difficult, the handle should be removed and replaced with this genuine OEM replacement part before using the appliance again. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This upper handle is a genuine MTD part, sold individually. It is compatible with the following outdoor appliance brands: MTD, Troy-Bilt, Yard Machines, Huskee, Craftsman, Yard-Man, and Bolens.

This throttle trigger is designed to open and close the throttle, or to control the speed of the engine. This part is mounted to the control handle on the equipment's shaft. With constant use, the throttle trigger may break or wear out. Use this genuine OEM throttle trigger in red to easily replace a damaged one. A screwdriver and long-nose pliers will be needed for the job. This OEM replacement throttle trigger is compatible with specific models of edgers and trimmers from Bolens, Craftsman, Cub Cadet, MTD, Ryobi, Troy-Bilt, and Yard-Man. It is sold individually.

This throttle cable is a used on string trimmers. This part links the carburetor assembly to the throttle trigger. Each throttle cable is made with a connector on each end. Over time, the throttle cable can be damaged or kinked through use. If this occurs, the cable will need to be replaced.Replacing the throttle cable will require basic tools and a set of work gloves. The first step to replacing the throttle cable is removing the original component. The throttle housing will need to be taken apart on each side of the string trimmer. The replacement cable will pass through the carburetor mounting plate hole and the engine housing before reassembling the rest of the parts.This throttle cable is sold as an individual component. It is a genuine OEM replacement part that is sourced directly from the manufacturer. The throttle cable is made for use with string trimmers manufactured by Yard Machines, MTD, Craftsman, Murray, Yard-Man, Bolens, and Cub Cadet.

This is an insulator assembly includes the insulator, seals, and hardware. It is designed to create the right spacing between the cylinder and carburetor on many blowers and trimmers made by various manufacturers. The insulator assembly also keeps heat from moving between the other components. Over time, the insulator assembly can become damaged or crack. When this occurs, air can reach the engine and create a condition where the engine can't perform at its best. If this happens, the insulator assembly will need to be replaced. Take off the air filter, drain the fuel, and remove the intake assembly. The insulator can be taken off of the engine before the replacement is added. Use mounting screws to fit the insulator to the other components. Reassemble the other parts to use the tool.This insulator assembly is a genuine OEM replacement part sourced directly from the manufacturer. It is sold as an individual part. This component is made to be used in leaf blowers, tillers, and string trimmers manufactured by Craftsman, Cub Cadet, Troy-Bilt, Murray, Yard Machines, MTD, Bolens, and Yard-Man.

This Craftsman carburetor is the component that mixes together gas and air before the mixture can reach the engine to power a lawn trimmer. If there isn’t enough fuel in the mix, it can damage the engine or cause the trimmer not to run. Too much fuel can create excess smoke, poor performance, or can prevent the engine from starting. Testing whether a carburetor needs to be replaced can be done by adding a small amount of fuel to the component after removing the air filter. If the engine begins to run but quickly sputters out, this is an indication that the carburetor has a problem. A replacement carburetor can be installed using a wrench, pliers, and safety glasses. This trimmer component is genuine OEM and comes directly from the manufacturer. It is compatible for use with lawn trimmers by Craftsman and MTD. This is an individual item that comes with the carburetor assembly and the carburetor gasket. Pliers and screwdrivers may be needed to complete this replacement or repair.

This replacement fuel cap is used with many types of gas-powered lawn and garden tools. The purpose of the fuel cap is to help keep dirt and debris out of the fuel tank. It also helps to reduce extra air from getting into the tank.Debris or air in the fuel tank can make it difficult to start a gas-powered machine. Dirt can cause damage to the engine, as well. The replacement fuel cap is a simple way to ensure these types of issues do not occur. Most fuel caps can last for many years without needing a replacement. However, over time, they could become damaged or worn out from too much use. The old cap can be removed and the new cap can be screwed onto the fuel tank to replace it. No tools are needed.The fuel cap can be used with trimmers and blowers from a range of manufacturers including Yard Machine, Cub Cadet, MTD, Craftsman, Murray, Remington, and Troy-Bilt. This is a genuine OEM part sourced from the manufacturer, and it is sold individually.

This OEM idle mandrel pulley kit includes the pulley, spacer/washer, and a bushing. This idle mandrel pulley spins the blade on a lawnmower deck of a tractor mower.A new idle mandrel pulley kit will be needed if the bearing for this pulley is damaged, broken, or lost because the bearing is not available by itself. If the bearing inside of the pulley is not spinning freely as it should, then the entire idle mandrel pulley kit will be needed to repair this machine. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment machines.This genuine MTD part is sourced directly from the manufacturer and sold individually. The idle mandrel pulley kit is compatible with lawn tractors manufactured by MTD, Yard Machines, Bolens, Yard-Man, Troy-Bilt, Poulan, Cub Cadet, Husky, and Murray.

This carburetor is designed for use with string trimmers. It comes with the full carburetor assembly. This part is used to create the perfect mixture of air and fuel before it is transported into the engine's combustion chamber. The carburetor is made of durable metal. If there is an issue with the carburetor, it may prevent the engine from starting even when the fuel tank is full. Sometimes the carburetor can also be clogged with dirt and debris.Before replacing the carburetor, it should be tested to be sure it is the problem. When the engine doesn't start but fuel is available, move to testing the component. The first step is to remove the air filter from the string trimmer. Add a teaspoon or so of fuel to the carburetor itself and try to start it. If it begins to run but quickly dies, the carburetor is likely the problem and will need to be replaced.This carburetor is a genuine OEM replacement part that is sourced directly from the manufacturer. It is sold as an individual part. The carburetor is made to be compatible with string trimmers manufactured by Cub Cadet and MTD.

This is a fuel cap. It keeps fuel from leaking or spilling, and slows fuel evaporation when a machine is sitting for long periods. The fuel lid can be cracked or otherwise damaged, or it can become lost when removed for refilling. For the safety of the operator, a missing or broken fuel cap should be replaced immediately.Replacing a fuel cap is simple. If there is an existing cap, remove it first by turning it counterclockwise. Install the new fuel cap by matching up the unit's threads and twisting it clockwise until secure. Wear gloves when working with fuel caps.This fuel cap is a genuine OEM part. It is made of high-quality, durable materials. The cap is sold as an individual piece. The fuel cap can be used with MTD, Cub Cadet, and Troy-Bilt machines. It is compatible with blowers, cultivators, edgers, trimmers, and other lawn and garden equipment.