Crosley Switch

This control-panel switch restores reliable on/off control of a selected function on your range or wall oven. Replacing a worn or intermittent switch helps ensure the appliance responds consistently when you toggle that function.

• Directs power to the associated circuit when switched on or off
• Common symptoms: function won't turn on/off, intermittent operation, or the switch feels loose/sticks
• Helps restore positive, consistent control from the backguard/control panel

• Disconnect power at the breaker before servicing
• Access the switch from the control panel/backguard; retain screws/clips
• Label/photograph wire positions and transfer leads one at a time to the new switch
• Ensure firm terminal connections, reassemble, restore power, and test operation

Fix water or ice dispenser not working with this 4-button control switch assembly. Common fix when buttons fail to respond or dispense incorrectly.

Oven light stays on or won't turn on when door opens? This door-activated switch restores automatic light control. Easy 15-minute DIY repair.

Fix intermittent burner failures or electrical issues with this range wiring harness. Restores power flow when connections are loose, burnt, or broken.

Washer overfilling or underfilling? The water level pressure switch senses tub pressure to control fill cycles. DIY repair in 20 minutes or less.

This is a factory switch used in the appliance's control/safety circuit. Replacing a worn or failed switch restores reliable signaling so the selected function engages properly and the unit responds consistently to user inputs and status conditions.

• Provides an electrical on/off signal to the control or safety circuit
• If faulty, selected functions may not activate or may be intermittent
• Can trigger error codes related to a switch input, depending on model

• Disconnect power before servicing; turn off gas/water if applicable
• Note/photograph wire locations and transfer connectors one at a time
• Verify actuator alignment and secure mounting before reassembly
• After installation, run a test cycle to confirm proper operation

Interior light won't turn on when door opens? This push-button door switch restores automatic lighting. Moderate DIY repair with basic tools.

This wiring harness routes power and control signals between key components inside your range or wall oven. Replace a damaged harness to restore safe, reliable operation and prevent intermittent heat, shorts, or non-working burners and oven functions.

• Distributes electrical power and signals between controls, switches, heating elements/igniters, and safety components
• Maintains correct connector orientation and wire routing for dependable operation
• Typical symptoms: no heat in oven or on surface burners, intermittent operation, breaker tripping, or visible burnt/melted wiring
• Restores stable connections to reduce arcing and overheating

• Disconnect power at the circuit breaker; for gas ranges, also shut off the gas supply
• Label or photograph all connections and transfer one wire at a time to avoid miswiring
• Route the harness exactly as original; keep away from sharp edges and hot surfaces; secure with existing clips/ties
• If connectors don't match or any terminals are heat-damaged, stop and inspect mating components.

Fix E32 error codes or washer stopping during fill with this water level pressure switch. Senses water level and controls fill cycles. DIY-friendly repair.

This is a door-activated switch that detects whether the oven door is open or closed. It controls functions such as the oven light or signals the control board about door position. Replace this switch if the oven light stays on or off regardless of door position, or if the oven does not operate correctly due to a faulty door signal.

Fix washer overflowing or not stopping fill cycle. This water level pressure switch senses tub water and signals control to stop filling. DIY repair.

This adjustable buzzer kit replaces a failed or noisy mini buzzer to restore audible alerts for cycles, timers and notifications. Compact design lets the appliance signal you reliably when cycles finish or need attention. What it does:

• Produces audible tones for cycle end, timers and other appliance notifications
• Replaces buzzers that are silent, intermittent, weak or emitting erratic beeps
• Helps you hear and identify completed cycles and timed alerts
• Small, mountable unit that fits behind the control panel and connects to the control board

• One adjustable buzzer kit

• Disconnect power before servicing to avoid shock risk
• Access may require removing the control panel; keep fasteners organized for reassembly
• Disconnect the buzzer wiring harness or connector before removing the old unit; connect the new buzzer the same way
• Test buzzer function with power restored before fully reassembling

This switch assembly restores electrical on/off control for a specific appliance function. Replace a worn or failed switch to stop intermittent operation and return reliable control to the affected circuit. What it does:

• Provides the electrical on/off or function control for the appliance circuit.
• Replaces a failed switch that can cause intermittent operation or unresponsive controls.
• Helps resolve symptoms such as a function that won't start, no response from the control, or erratic switching.
• Connects to the existing wiring harness and mates with the original mounting points.

• Disconnect power to the appliance before beginning any work.
• Remove the appropriate access panel to reach the switch; note wire and terminal locations before disconnecting.
• Unplug the wiring harness or carefully detach terminals, swap the switch assembly, then reconnect securely.
• Restore power and verify the replaced switch operates the function correctly.

Dishwasher won't start or stops mid-cycle? A faulty door switch prevents operation when it can't detect the closed door. Simple DIY repair.

Fix unresponsive or erratic cycle selection with this rotary encoder switch. Mounts behind the control knob to restore accurate cycle settings and indicators.

Interior light stays on or won't turn on when door opens? This door-activated switch restores automatic on/off lighting. Easy 15-minute fix.