Crosley Washer Parts

18 year old Maytag Atlantis top load washer had a load knocking and rattle sound with excessive vibration when the tub was spinning, but not when it was agitating. They was no water leaking. I took the front panel off and carefully listened while I ran a cycle and the loud sound sounded like it was coming from the drain pump. So I took off the drive belt and noticed that it was glazed and that there was belt material on the drain pump and tub transmission pulleys. I removed the drain pump and... Read more

• Noisy

I just wanted to put my experience here for all to see. I have a Maytag Neptune, MAH5500BWW, one of the original ones. I bought it back in 2002 and it has done many many loads of wash faithfully. So when the bearings started to get loud I thought it best to replace them, the seal kit and the belt. I did my research as best I could and decided to order the OEM parts from an appliance supplier. If you are replacing the bearings, watch on line videos prior to performing the job. It will... Read more

I purchased part #85753076A, Whirlpool Fabric Softener Dispenser. Popped off the top from the agitator and popped on the fabric softener dispenser. It took me less than a minute and it works perfectly! No more missing the rinse cycle!!! Read more

My Mom's Kenmore had a burnt plastic smell after a thunderstorm. Found motor capacitor had melted through, dumping liquid platic "spaghetti" onto the insulation blanket under the washer. All other compents looked fine. Told her not to use it until I replaced capacitor. The washer is 4 yrs old but the new capacitor revision was 3 letters higher, so they've made some design changes. Externally it looks the same. There is a large number on the capacitor, but the part is ordered by the much... Read more

Water valve not closing all the way. Water keep entering washer even with power cord unplugged. Parts I ordered fit perfect. Ordered on Thursday night , parts there Saturday. Great service and shipping. Thank Read more

My teenaged son took the old washer door off and apart. He replaced our glass from our washer onto the new doors and attached it to the hinge. These doors are compatible with Kenmore washer even though it says Frigidaire. Read more

There was a horrible screeching noise coming from the washer, and upon inspection I found that the retaining nut that attaches the cam to the machine was either improperly tightened to begin with or had worked itself loose causing the cam to wobble and the belt to work down the cam. The cam gear teeth became worn and the belt worked itself half off the cam and cut a hole in the protective plastic screen containing the whole ensemble. I purchased the belt, shield and cam kit. The parts are... Read more

Replaced with thrust bearing kit. Watched your video and it took about 10 minutes to fix. Thanks Read more

• No hot or cold water
• Will not stop filling with water
• Will not fill with water
• Leaking

This is my third repair of this type. The first was a stand-alone washer and was very easy, because there was a plate on which the inlet valve assembly was mounted, and it was easily removed. This repair was on a Frigidaire stacked washer/dryer (laundry center). Stacked washer/dryers are typically purchased to save space and are often tucked into a closet. Be sure you can pull it out to access both front and rear. Remove drain hose from drain, detach water hoses, electricity and dryer vent... Read more

Ordered the part got it in 2 days Read more

• Will not fill with water
• No hot or cold water
• Will not stop filling with water

I called Appliance pros and asked for a diagnosis. They gave one and sent me the part. It took 15 min. and it worked perfectly. Also got super fast delivery on the part. Thank you!! Read more

Replaced the rear drum bearing assembly and the front top felt that the drum rides on and since I has it apart installed a new belt. Simple to do and takes very little time! Read more

• Shakes and moves

With more difficulty and frustration than expected but it works fine now. Things learned: 1. Order only 3 replacement pins. One comes with the shocks that you can't be sure you see in the picture. 2. A circuit board in a plastic box mounted to the floor, left rear, must be removed by two screws to be able to get pliers onto the head of the pin more easily. This helps installation too. 3. A 1/2" deep socket pushed onto the retaining tab of the pin stays there while you pull with pliers from the... Read more

Got online and searched for part by washer model number. Found AppliancePartsPro.com. They listed diagram of part. I ordered it online and received it next day with no extra charge for fast delivery. My husband attached cosmetic drawer cover to detergent drawer part we ordered in a few minutes. It fits and is working! Speedy service was appreciated. Read more

Since I hadn't found the Tech Sheet for the washer (which there should be one inside the top cover) I simply thought I'd buy the drive motor (and a new belt, a.k.a "cheap insurance"). Installed the motor once I'd received it from AppliancePartsPros, the washer worked a couple of cycles then gave me the same "SrV CLL" message. I didn't know how to access the error codes on this model but found the info in the Tech Sheet, so I checked it and got an E53 code. Since I'd replaced the motor... Read more

Replaced springs and shocks. Read more