Defrost Heater, Icing Kit, Fountain Heater

This defrost heater melts frost and ice from the refrigerator evaporator so the cooling system runs efficiently and food stays properly chilled. It restores normal auto-defrost operation when the original heater has failed. What it does:

• Heats the evaporator coil during the defrost cycle to remove frost buildup
• Helps maintain consistent cooling by preventing ice that can block airflow
• Common symptom: visible frost or ice buildup on the evaporator or inside the freezer
• Common symptom: reduced cooling performance or longer run times between cycles

• Always disconnect power to the appliance before replacing the heater to avoid shock
• Access typically requires removing the evaporator cover inside the freezer
• Inspect and replace any damaged clips, mounts, or wiring; harness connections are secure
• Test the heater for continuity (and check associated thermostat/thermistor) before final reassembly

This heater assembly provides the high heat source used to dry clothes faster by warming the air inside the dryer. It replaces a failed or damaged heating element to restore normal drying performance and temperature. What it does:

• Generates the heated air needed for effective drying
• Commonly replaced when dryer produces little or no heat
• Can cause tripped thermal cutoff or heating-circuit issues when failed

• One heater (heating element) assembly as shown

• Disconnect power before starting; this part involves live-voltage components
• Inspect associated thermostats, fuses, and wiring; replace faulty safety parts as required
• Handle the element carefully — edges may be sharp and terminals can be damaged by rough handling

This defrost heater melts frost and ice from the freezer evaporator so the refrigerator can maintain proper airflow and cooling. Replaces a failed heater to restore normal automatic defrost cycles and prevent excessive frost buildup. What it does:

• Gently heats the evaporator coils during the defrost cycle to remove accumulated ice.
• Helps restore normal airflow and temperature by preventing heavy frost or ice buildup.
• Commonly used when you see repeated frost on coils, ice on the evaporator, or poor cooling performance.
• Works with the existing defrost control/thermostat to run only during defrost cycles.

• One defrost heater assembly

• Disconnect power before accessing the evaporator compartment or any wiring.
• Install requires removing interior liners or evaporator cover—follow your model's service manual.
• Inspect and test the defrost thermostat and bi-metal or control board if the heater failed; replace as needed.
• Avoid touching the heater element or bending evaporator fins; handle components carefully.

This defrost heater melts frost and ice build-up on the evaporator to restore normal airflow and cooling. Replacing a failed heater helps prevent recurring frost and improves temperature consistency in the freezer compartment. What it does:

• Heats the evaporator coil during the defrost cycle to remove accumulated frost and ice.
• Restores proper airflow and cooling when frost buildup is preventing normal operation.
• Common symptom: visible frost/ice on evaporator or evaporator cover.
• Common symptom: freezer running but cooling inconsistently or icing up.

• Disconnect power to the appliance before starting any repair.
• Inspect and replace only with the exact part number; handle the heater element carefully to avoid bending or damage.
• Reinstall evaporator cover and any seals; test a complete defrost cycle after replacement.

This defrost heater kit heats the evaporator to melt frost and ice buildup so the refrigerator can cycle normally and maintain proper cooling. It's a direct-replacement kit for units that use a heater-style defrost assembly. What it does:

• Warms the evaporator coil during the defrost cycle to remove frost and ice
• Helps restore normal airflow and cooling when frost buildup blocks the evaporator
• Commonly used when a refrigerator has excessive frost, poor cooling, or no active defrost
• Works with the existing defrost control and thermostat to allow automatic defrost cycles

• Disconnect power to the appliance before starting any service
• Handle evaporator fins and sharp sheet metal with care; wear gloves and eye protection
• Reassemble panels and restore power; check for proper defrost operation after installation

This dispenser heater kit warms the dispenser area to help prevent ice build-up and keep the water/ice dispenser operating reliably. Replaces a failed heater assembly to restore proper dispenser function. What it does:

• Heats the dispenser chute/valve area to reduce frost and ice clogging
• Helps restore reliable water or ice dispensing when the dispenser intermittently freezes
• Prevents repeated thaw cycles that can cause leaks or inconsistent dispense flow
• Works as the direct replacement heater component used in the dispenser assembly

• Disconnect power to the appliance before beginning any work
• Access may require removing the dispenser housing or control panel
• Handle electrical connections carefully and secure wiring per OEM routing

This fixture heater is the heater assembly used to warm a targeted appliance component so the unit operates correctly and resists ice buildup. It restores heat where a small, localized heater is required. What it does

• Provides localized heat to a fixture or component to prevent freezing and help normal operation.
• Warms internal surfaces that can collect frost or condensation, reducing ice buildup.
• Restores heat when a failed heater causes intermittent or no warming at the fixture.
• Helps eliminate symptoms such as frost accumulation, poor component function, or temperature-related faults.

• One fixture heater assembly.

• Disconnect power to the appliance before starting any repair to avoid shock or injury.
• Handle terminals and wiring carefully; match wire connections and secure all fasteners.
• Use basic hand tools; for correct routing and placement.

This defrost heater for the freezer evaporator melts frost and ice buildup so the cooling system can run efficiently. It restores normal defrost cycles and helps prevent ice-clogged evaporators that reduce cooling performance. What it does:

• Warms the evaporator coil during defrost cycles to remove accumulated frost and ice
• Helps restore proper airflow and temperature control in the freezer compartment
• Commonly replaced when evaporator icing prevents the freezer from cooling properly
• Works with the defrost control and thermostat to complete timed defrost cycles

• One defrost heater assembly

• Disconnect power to the appliance before starting any repair
• Access typically requires removing evaporator cover panels inside the freezer; handle the evaporator fins and heater carefully to avoid damage
• Verify continuity of the heater with a multimeter before and after installation; replace related defrost components if they also test faulty

The Water Tank Heater is an OEM component for GE bottom-mount refrigerators offering internal water and ice dispensing. Located within the drinking water reservoir, it facilitates antibacterial heating cycles. Dependable water delivery relies on a functioning tank heater.

Symptoms of failure include:  

• Absence of hot water from the dispenser or ice maker
• Cloudy or sedimented water quality needs frequent filter changing  
• Mold or bacterial growth detected within the reservoir

Causes involve cracked or porous heater elements that cannot transfer thermal energy effectively over extended years, loose wiring terminals cutting off electric current, or mineral buildup hindering heat transfer to the surrounding tank.

Replacing with this genuine GE heater ensures optimized reservoir sanitization through precise temperature regulation. Compatible replacements include models for Hotpoint, RCA, and Kenmore side-by-side refrigerators seeking to restore hot water dispensing and purification features.
 

This refrigerator temperature sensor detects fresh-food compartment temperature and provides the thermostat/control board with the readings needed for proper cooling management. Replacing a failed sensor restores accurate temperature feedback to the control system. What it does:

• Measures internal fresh-food compartment temperature for the control board
• Helps the fridge regulate run cycles to maintain set temperatures
• Faulty sensor can cause incorrect temperature display or inconsistent cooling

• Always unplug the appliance before attempting any repair.
• Handle the sensing tip and wiring harness gently to avoid damage.
• Use basic hand tools; follow the wiring diagram for location and routing.