Dishwasher Clip Or Clamp

This spring-style clamp secures flexible hoses and tubing on appliance water and drain connections to help stop leaks and maintain a tight seal. A simple replacement when original clamps corrode or lose tension. What it does:

• Holds hose or tubing firmly on barbed fittings to prevent leaks and disconnections
• Restores reliable sealing on water inlet, drain, or vent hose connections
• Commonly used where a compact, tensioned clamp is required
• Helps stop symptoms like dripping, puddling, or loose hose connections

• One spring-style clamp

• Turn off power and water supply to the appliance before servicing
• Use pliers to expand the clamp for removal and installation; avoid sharp tools that can damage the hose
• Replace any hoses or fittings that show damage or excessive wear

This E-ring retaining clip secures shafts, axles, and components to prevent lateral movement and keep assemblies aligned. It's a small, spring-steel fastener that restores proper fit and reduces noise from loose parts. What it does

• Holds shafts, rods, and spindles in place to prevent sliding or disengagement
• Restores stable alignment for rotating or sliding assemblies
• Helps stop rattling, clunking, or parts shifting during operation
• Provides a low-profile, durable retention solution for pivot points and axles

• Disconnect power and move appliance to a safe, stable work area before starting
• Use appropriate snap-ring/needle-nose pliers or a small screwdriver to remove and install; E-rings can spring outward
• Inspect mating grooves and shafts for wear; replace clip if deformed or worn
• Wear eye protection and handle carefully—small metal clips can be sharp and may fly off when compressed

This sump retainer secures the appliance sump assembly and helps keep the pump seal and surrounding components properly positioned to reduce leaks and maintain correct water flow. It's a small replacement part used during sump or pump repairs. What it does:

• Holds the sump housing or pump assembly in place to maintain a reliable seal
• Helps prevent water leaks from the pump/sump area when installed correctly
• Keeps internal components aligned for proper water circulation and drainage
• Commonly replaced when sump hardware is cracked, warped, or no longer secures the pump

• One sump retainer

• Power off and unplug the appliance before starting any repair
• Verify you have full access to the sump/pump area; removal of panels or racks may be required
• Inspect surrounding seals and gaskets; replace if damaged to ensure a watertight fit

Red

This small metal ring clip secures wiring and small assemblies in place to prevent movement and wear. It restores proper retention so harnesses and parts stop rubbing, rattling, or coming loose. What it does:

• Locks a wire, tube, or small component into its mounting position to prevent chafing or disconnection
• Helps stop intermittent electrical contact or noise caused by loose wiring
• Reduces vibration-related wear on nearby parts and connectors
• Commonly used where a compact, spring-style retention is needed

• One ring clip

• Turn off and unplug the appliance before inspecting or replacing clips
• Remove panels or trim per the manufacturer's service instructions to access the clip location
• Use needle-nose pliers to compress or expand the clip as needed; avoid bending it out of shape
• Replace any damaged clips—do not reuse if deformed or fatigued

This clamp secures flexible hoses and small-diameter tubing to fittings, helping prevent leaks and maintain proper fluid flow in appliance systems. It's a simple replacement that restores a tight, reliable connection. What it does

• Holds a hose or tube firmly on a barb or nipple to stop leaks and loss of pressure
• Keeps water, drain, or vent hoses seated during normal appliance operation
• Replaces worn, corroded, or loose clamps that cause dripping or poor connections
• Works where a small, durable clamp is required for routing or securing tubing

• One hose clamp

• Inspect hose and fitting for damage; replace hose if cracked or hardened before installing the clamp
• Tighten clamp until snug—do not overtighten; ensure even compression around the hose
• Disconnect power and water as appropriate and take safety precautions before working on the appliance

This clamp secures a flexible appliance hose to a fitting to help prevent leaks and keep connections tight. It's a small but essential part that restores a proper seal on water or drain lines. What it does:

• Holds a hose firmly to a tailpiece, barb or connector to reduce leaks and hose slippage
• Helps stop intermittent dripping or pooling caused by loose hose connections
• Restores a proper seal after hose replacement or maintenance
• Works on common appliance water/drain lines where this clamp style is used

• One hose clamp

• Disconnect power and shut off water to the appliance before starting any work
• Allow the appliance and hoses to cool if recently used; use gloves and eye protection
• Use appropriate pliers or a screwdriver (depending on clamp style) to remove and install the clamp; avoid over-tightening
• Inspect the hose and fitting for damage; replace the hose if cracked or worn

This sump clamping nut secures the washer/dishwasher sump seal and housing, helping keep the sump assembly sealed and stable during operation. It's a small but essential fastener for preventing leaks and maintaining proper drainage. What it does:

• Holds the sump/tub seal and sump housing tightly in place to maintain a watertight connection
• Prevents the sump assembly from loosening during spin or wash cycles
• Helps reduce leaks and related water damage when installed correctly
• Works with the factory sump and seal components as the retaining nut

• Replace only with the matching part number; verify orientation before tightening
• Hand-start threads to avoid cross-threading, then tighten to factory spec (do not overtighten)
• Disconnect power and water to the appliance before servicing

A replacement clamp that secures hoses or wiring to keep lines routed and stable, helping prevent rubbing, leaks and noise. Restores a reliable hold for tubing and harnesses so the appliance runs quietly and safely. What it does:

• Holds hoses, tubing or wire harnesses in place to reduce movement and chafing.
• Helps prevent leaks and water line abrasion caused by loose fittings.
• Reduces rattling or vibration from unsecured lines or cables.
• Keeps routing organized so adjacent components aren't stressed or worn.

• Disconnect power before servicing the appliance; shut off water supply when working on water or drain lines.
• Remove the old clamp and position the replacement so it fully engages the hose or harness, avoiding twists.
• Use appropriate hand tools (pliers or screwdriver) and secure the clamp evenly; avoid overtightening.
• Inspect surrounding hoses and wiring for damage while installing; replace any components that show wear.