Dishwasher Clip Or Clamp

This replacement part is a fastener, and it is intended for use in different types of appliances. This is a genuine replacement part made by Frigidaire. Fasteners are a small metal part that is used in many spots in refrigerators or freezers. These clips are able to help keep shelving and other items in place so that the appliance works properly. A new fastener might be needed if there are any parts of the fridge or freezer that are loose or falling off. The fasteners allow the shelving and other attachments to stay steady, so if anything is not attached properly, it might be time to replace the fasteners. It is possible that the fasteners might become brittle over time as they are typically held in cool or freezing conditions. Many appliances require more than one fastener so be sure that the correct amount is ordered. This fastener is sold individually and is compatible with appliances made by Frigidaire. Also note that this part is a genuine OEM replacement part.

This clip is a small retainer used to secure panels, wiring, or hoses so components stay in place and operate quietly. It prevents loose parts from shifting during normal use and helps maintain appliance fit and finish. What it does:

• Holds wiring, harnesses, or small hoses in position to prevent rubbing or disconnection
• Keeps trim or access panels seated to reduce vibration and noise
• Helps maintain correct routing to avoid wear on wires and hoses
• Commonly replaced when the original clip is broken, cracked, or missing

• One clip

• Disconnect power to the appliance before attempting any repair
• Access the area and remove any panels or covers that block the clip location
• Press the clip into its mounting slot or snap the harness into the clip until it seats securely
• Replace any damaged surrounding fasteners or retainers; do not use damaged clips

This clamp secures a flexible appliance hose or tube to prevent leaks and keep connections tight. It restores proper hose seating so water or air flows where it should, reducing drift and seepage. What it does:

• Fastens a hose or tube to a barb, fitting, or pipe to maintain a sealed connection
• Prevents hose slippage that can cause leaks or reduced performance
• Helps stabilize hoses that vibrate or move during normal appliance cycles
• Commonly used on water, drain, or vent hoses in laundry and kitchen appliances

• One clamp

• Turn off and unplug the appliance and shut off water supply before starting
• Use appropriate pliers or a screwdriver for the clamp type; avoid crushing the hose
• Inspect hose and fitting for damage and replace if needed

A small spring-style hose clamp that secures flexible hoses to fittings, helping prevent leaks and keep connections tight. Ideal for replacing corroded, stretched, or damaged clamps on compatible Whirlpool appliances. What it does

• Compresses around a hose to hold it firmly on a barb, spud, or outlet fitting
• Restores a secure seal to reduce leaking at hose connections
• Commonly used on drain, fill, and water supply hoses where spring clamps are specified
• Helps maintain proper appliance operation by preventing hose slippage

• Disconnect power and water before servicing the appliance
• Use pliers to expand the clamp for removal and to seat it during installation; ensure clamp sits evenly over the hose bead
• Replace any hose that shows cracks, soft spots, or excessive wear rather than reusing a damaged hose
• Dispose of the old clamp safely; wear eye protection when compressing spring clamps

This ring nut and clamps assembly secures the washer tub/housing connections so seals and hoses stay tight during operation, helping reduce leaks and excess movement. What it does:

• Holds tub or hose fittings firmly in place to maintain a water-tight connection
• Helps prevent leaks caused by loose or worn fastening hardware
• Restores proper alignment to reduce vibration or rubbing from loose components
• Used when replacing corroded, broken, or missing retaining hardware

• Disconnect power and water before starting any repair to avoid shock or flooding
• Basic hand tools required; access panels may need to be removed
• Tighten clamps to secure fit but avoid overtightening plastic fittings

This E-ring is a small retaining clip that secures shafts, spindles, and components to prevent lateral movement and keep assemblies in place. It restores proper alignment and helps stop parts from slipping off their shafts. What it does:

• Secures shafts and spindles by fitting into a groove to lock components in place
• Prevents lateral movement and component disengagement during operation
• Helps stop rattling or misalignment caused by loose parts
• Small, simple part used where a snap-in retaining clip is required

• Disconnect power before servicing and follow all safety guidelines
• Use snap-ring/needle-nose pliers or appropriate tools to install/remove carefully
• Ensure the ring seats fully in the groove and that the mating parts are correctly positioned
• Inspect mating shaft and groove for wear; replace if damaged