Dishwasher Hose Or Tube

Routes wastewater from your dishwasher pump to the home drain. Replace if cracked, kinked, punctured, or worn to restore proper drainage and prevent leaks.

90-degree rubber elbow connecting drain hoses in your dishwasher. Replace if cracked, split, or leaking. Installs between pump and drain line.

Channels wash water through your dishwasher's spray system. Replace if cracked, leaking, or clogged to restore proper water distribution and flow.

Carries water from home supply to washer inlet valve. Replace if your hose is cracked, worn, leaking, or damaged by pests or age. Restores proper fill.

Fuel line connector hose for gas walk-behind mowers. Replaces cracked, dried out, or leaking fuel hoses. Installs between tank and carburetor.

Replaces cracked, split, or rodent-damaged connector hoses that route water between internal dishwasher components. Essential when the original hose leaks.

Connect hot and cold water faucets to your washer's inlet valves with this 2-pack of 5-foot fill hoses. Replace aging, cracked, or leaking supply lines.

5 foot. Package of 2.

Water line kit for connecting ice makers to household water supply. Includes copper tubing, valve, and fittings for installation under kitchen sink.

This drain hose routes and removes wastewater from the appliance so it can pump out normally and avoid standing water. It's a direct-fit service part used to restore proper draining. What it does

• Carries wastewater from the appliance pump to the household drain or air gap
• Restores normal draining when original hose is cracked, split, or leaking
• Helps prevent water backing up into the appliance when properly routed and secured
• Can stop intermittent leaks or reduced drain performance caused by hose damage

• One drain hose

• Disconnect power and turn off water supply before starting any repair
• Inspect hose routing and replace with the same path to avoid kinks or high loops that trap water
• Secure hose connections with appropriate clamps; tighten but avoid over-torquing
• After installation, run a short drain cycle and check all connections for leaks

Hose assembly for portable dishwashers. Connects your unit to the sink faucet for water supply. Replace if cracked, leaking, or stripped threads.

This fill and drain hose assembly routes water into and out of the washer, helping the machine fill, drain and operate normally. Replacing a worn or damaged hose prevents leaks and restores reliable water flow. What it does

• Carries incoming water to the washer tub during the fill cycle.
• Provides a path for water to exit during drain/spin cycles.
• Commonly replaced for visible cracks, pinholes, leaks, or kinking that restricts flow.
• Can resolve symptoms like water on the floor, poor filling, or incomplete draining.

• Turn off power and shut off water supply before beginning work.
• Inspect hose routing and fasteners; replace any damaged clamps or connectors.
• Tighten connections securely and test for leaks at low flow before a full cycle.

This stainless C06 installation clip secures trim and panels to the dishwasher frame, restoring proper fit and finish. Use it to replace a worn or missing clip for a stable door appearance and reduced rattling. What it does:

• Secures the outer panel/trim to the dishwasher cabinet so the door sits flush
• Helps stop trim or panel movement that can cause rubbing or rattling noises
• Restores proper alignment after repairs or panel removal
• Matches stainless trim for a consistent finished look

• Designed for panel/trim attachment; install with the appropriate screws or fasteners for your model
• Disconnect power before servicing the dishwasher door to avoid injury
• Keep clips and small fasteners out of reach of children
• Replace all affected clips to maintain even panel alignment

Kit contains two 10 feet inlet hoses.

Dishwasher drain hose kit connects the dishwasher pump to your home's drain system. Replace if cracked, leaking, or damaged. Includes clamp.

Size: 6 foot long. Washers not included. This is one hose, for a set with washers order 285363. For inlet hose screen use 285452A and for inlet hose washers use 285448A