Dryer Bearing Parts

This cleaning felt mounts on the dryer's front shroud. It lightly contacts the rotating drum to wipe away lint and residue, helping keep the drum edge clean and supporting consistent airflow to the lint filter.

• Provides a soft wiper against the drum rim to reduce lint and residue buildup
• Helps maintain smooth drum rotation and a clean front duct area
• Wear signs include frayed or missing felt, lint trails on fabrics, or light squeaks at the front
• Visual inspection is recommended if lint accumulates inside the drum after cycles

• Disconnect power; for gas dryers, also shut off gas supply
• Access the front panel/shroud and note the original felt's orientation before removal
• Clean the mounting surface; install the new felt in the same position (some models use clips or adhesive)
• Hand-rotate the drum to ensure even, light contact before reassembly and testing

Supports smooth drum rotation in your dryer. Replace if you hear squeaking, whistling, or rumbling during cycles. Verify fit with your model number.

The Duct Trap Housing is an OEM component specifically designed for GE laundry machines. It serves as the housing and base unit for the duct trap or lint trap that collects lint and debris during the drying cycle. The duct trap housing is designed to seamlessly integrate with the dryer vent and ducting system.

Causes of a bad duct trap housing include cracks or warping from heat exposure over time, damage due to impact or mishandling, or worn-out mounting components that secure it in place.  

Symptoms of a bad duct trap housing include:

• Excessive lint buildup inside the dryer indicating incomplete lint removal  
• Airflow issues such as longer dry times or wet clothes after a full cycle
• Venting problems like drafts or leaks at the vent connection
• Noise or vibration originating from the vent area

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Right hand side. Used most Admiral, Crosley, Norge, and Magic Chef dryers. Includes glide and felt pad.

Supports the front drum edge for smooth, quiet rotation. Replace when worn to stop scraping noises or drum wobble. Confirm fit with your model number.

Drum bearing assembly enables smooth drum rotation in your dryer. Replace if you hear squealing or grinding noises during cycles. Confirm fit with your model.

Drum glide supports the front of your dryer drum for smooth rotation. Replace when you hear scraping or squeaking sounds. Confirm fit with your model.

Supports smooth drum rotation in your dryer. Replace when you hear squealing, grinding, or notice excessive drum wobble during cycles. Confirm fit with your model number.

The Trap Duct Assembly for Dryer is an OEM replacement part for GE dryers. It forms the internal ductwork connection between the dryer drum and the vent tube. This assembly is critical for proper airflow and efficient moisture removal during the drying cycle. 

Causes of a bad trap duct assembly can include cracks or loose connections due to heat fatigue over many cycles. Ducts must withstand temperature swings and mechanical stresses.

Symptoms of a bad trap duct assembly include:

• Increased drying times 
• Excess condensation or moisture remaining in clothes after cycles
• Visible cracks or damage to ducts

This GE replacement part is compatible with Hotpoint, RCA, and Kenmore dryer models. 

Secures and supports the rotating drum shaft for smooth, quiet operation. Replace if your dryer squeals, wobbles, or drags. Confirm fit with your model.

Supports the front edge of your dryer drum for smooth, quiet rotation. Replace when you hear scraping or squealing sounds. Verify fit with your model.

This duct trap redirects and contains exhaust from the appliance's ventilation opening to help guide airflow and capture debris before it enters the main ductwork. It's a direct-replacement service part designed to restore proper vent routing and reduce buildup in the duct path. What it does:

• Funnels exhaust from the appliance outlet into the duct system for proper ventilation
• Helps prevent large debris and lint from entering the main duct run
• Restores correct vent alignment and sealing for efficient airflow
• Commonly replaced when damaged, cracked, or allowing exhaust leaks

• One duct trap

• Disconnect power to the appliance before starting any work; if gas is present, follow gas-safety shutoff procedures
• Access may require removing the rear/discharge panel or lowering the appliance; keep track of fasteners
• Inspect adjoining ductwork and seals; replace or reseal with appropriate high-temp duct tape when reinstalling
• Wear gloves and eye protection

Supports the front rim of your dryer drum for smooth, quiet rotation. Replace when you hear scraping or squealing to restore proper drum support.

Cushions drum contact points to reduce noise and metal wear in your dryer. Replace when worn, torn, or missing to restore quiet operation. Confirm fit with your model number.

Supports the front drum edge for smooth rotation. Replace when you hear squeaking or scraping sounds. Confirm fit with your dryer model number.

The Trap Duct Assembly is an OEM replacement part for GE dryers. This assembly provides the ducting and pathway to direct lint from the dryer drum to the lint trap. It plays a crucial role in efficiently removing lint and preventing blockages. 

Causes of a bad trap duct assembly can include cracks or breaks in the ducting material, crushing or collapsing of the duct, or loose connections that allow lint to bypass the trap. 

Symptoms of a bad trap duct assembly include:

• Increased drying times as lint is not properly exhausted 
• Lint building up inside the dryer instead of collecting in the trap
• Vibrating or rattling noises from loose or damaged ducting
• Reduced airflow leading to inefficient drying performance

This GE replacement part is compatible with Hotpoint, RCA, and Kenmore models. Replace yours today for optimal lint removal and dryer operation.