Dryer Fuse Or Sensor

This cycling thermostat regulates on/off heat cycles to maintain consistent operating temperature. Replacing a failed thermostat restores proper temperature control and helps protect the appliance from overheating or underheating during normal operation.

• Senses internal temperature and opens/closes contacts to control the heating circuit
• Helps prevent overheating; supports stable, repeatable heat cycling
• Common failure symptoms include no heat, overheating/shutting off too soon, or longer-than-normal run times
• Electrical component—failure may be intermittent before complete loss of function

• Disconnect power (and gas supply, if applicable) before service
• Note wire locations; transfer connectors one at a time to the new thermostat
• Mount firmly against the mating surface for accurate temperature sensing
• After installation, verify proper operation and temperature cycling

This fixed, non-adjustable thermostat switches at approximately 140°F to control or limit temperature in the appliance. Replacing a fatigued thermostat restores accurate temperature regulation and helps prevent underheating, overheating, or erratic cycling.

• Senses temperature and changes state near 140°F to switch a circuit as designed
• Helps regulate heaters, fans, or act as an over-temperature protector
• Failure can cause no heat/low heat, runs too hot, or inconsistent cycling
• May prevent a fan or heater from turning on or off when expected

• Disconnect power and allow components to cool before servicing
• Verify the temperature rating and terminal style match the original
• Note wire positions; transfer any mounting clips/insulators from the old part
• Ensure firm, clean contact with the mounting surface; avoid overtightening or flexing the disc

This cycling thermostat regulates the dryer's heat by sensing exhaust air temperature and switching the heater on and off. Replacing a faulty thermostat restores consistent drying performance and helps prevent underheating or overheating.

• Monitors dryer air temperature and cycles the heating element or gas burner to maintain the proper range
• Helps prevent overheating that can trip safety limits
• Failure can result in no heat, low heat/long dry times, or heat that doesn't cycle correctly
• May cause intermittent shutdowns due to temperature issues

• Disconnect power; if gas, also shut off gas supply before servicing
• Thermostat is typically mounted on the blower housing or exhaust duct
• Note/transfer wires to the same terminals and secure the thermostat with existing screws; ensure it seats flush to the housing
• After replacement, clean lint buildup and verify proper vent airflow to avoid repeat temperature problems

The Electrode is an OEM replacement part for Whirlpool dryers. It is responsible for detecting the moisture levels in your laundry during the drying cycle, allowing the dryer to automatically adjust the drying time and temperature. It helps prevent over-drying or under-drying of your clothes, saving energy and protecting them from potential damage.

A bad electrode can occur due to wear and tear, damage, or a buildup of debris or lint. If you notice symptoms such as clothes taking longer to dry, the dryer shutting off prematurely, or inconsistent drying results, it may be time to replace the moisture sensor bar electrode.

Symptoms of a bad electrode include:

• Clothes taking longer to dry than usual
• The dryer shutting off prematurely
• Inconsistent drying results, with some items remaining damp

Repair your dryer by replacing the faulty or damaged electrode with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This safety thermostat is a temperature-sensitive switch for dryers. It monitors internal heat and opens the circuit if temperatures climb too high, helping prevent overheating. Replacing a failed thermostat restores proper heat control and safe operation.

• Monitors dryer temperature and cuts power to the heater if the limit is exceeded
• Helps protect against overheating and heat-related shutdowns
• Common symptoms of a failed or tripped thermostat: no heat or intermittent heat, dryer running too hot, or cycles ending early due to overheating
• Overheating or repeated trips often indicate restricted airflow—inspect venting and lint paths

• Disconnect power; for gas dryers, also shut off the gas supply
• Access the thermostat location per your model's service information
• Note wire positions and transfer them one at a time; mount the thermostat flush to its mating surface
• After installation, clear lint and verify proper airflow through the exhaust and vent

This 155°F-rated electric dryer thermostat monitors and controls drum temperature. It cycles the heating element to maintain proper heat so loads dry consistently while helping protect the appliance from overheating.

• Regulates dryer temperature on electric models
• Controls heater cycling to maintain proper drying temperatures
• Failure may cause no heat or weak heat
• May lead to overheating or longer-than-normal dry times

• Disconnect power before servicing
• Access the thermostat for your model, note wire positions, and transfer connectors one at a time
• Mount the thermostat flat and secure for proper thermal contact
• Reassemble, restore power, and test a cycle for proper heating

This internal-bias thermostat controls exhaust temperature in your dryer, cycling the heat on and off to maintain proper drying temperatures. Replacing a failed thermostat can restore consistent drying performance and help protect the dryer from overheating shutdowns.

• Monitors exhaust air temperature and opens/closes the heating circuit to regulate heat
• Provides the bias function used by automatic cycles for correct temperature control
• Failure symptoms can include no heat or low heat, long dry times, overheating or high-limit trips, and inconsistent cycling temperatures
• Helps prevent thermal cutoffs caused by restricted airflow or faulty temperature regulation

• Disconnect power before servicing; for gas models, also shut off the gas supply
• Access location is typically on the blower/exhaust housing; note wire positions and transfer one at a time
• Ensure the thermostat mounts flush for proper sensing; tighten screws securely
• After replacement, verify good airflow and clear venting to prevent repeat failures

This thermostat is a temperature-sensitive switch that opens and closes the heating circuit to control heat. Replacing a worn or failed thermostat restores consistent temperature regulation and helps protect your appliance from overheating, shutdowns, or underheating.

• Monitors internal temperature and cycles the circuit on and off as designed
• Helps prevent overheating by opening at its calibrated threshold
• Failure can cause no heat, overheating, or intermittent cycling
• Irregular temperatures or longer run times are common symptoms

• Disconnect power (and shut off gas, if applicable). Allow the appliance to cool completely before service.
• Note wire positions; transfer one lead at a time to the new thermostat.
• Mount the thermostat firmly/flush against its mating surface or bracket for accurate sensing.
• Use a multimeter to check continuity per your model's service specs; replace if out of tolerance.

The Thermostat is an OEM component specifically designed for GE dryers. As a key component responsible for regulating heat, this thermostat plays an important role in the drying cycle. It monitors and controls the temperature of the dryer, ensuring clothes are thoroughly dried without being overheated or damaged. 

Causes of a bad thermostat can include wear and tear over time, exposure to high heat levels that degrade electronic components, or damage from moisture or impact. 

Symptoms of a bad thermostat include: 

• Inefficient or prolonged drying times 
• The dryer not heating up properly
• Fluctuations in temperature
• The dryer not starting or functioning correctly

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This dryer control thermostat regulates internal temperature by cycling the heater on and off. Replacing a failed thermostat restores proper, consistent drying temperatures to protect fabrics and improve overall drying performance.

• Monitors exhaust temperature and opens/closes contacts to maintain target heat
• Helps prevent underheating and overheating during drying cycles
• Common symptoms of failure: no heat or low heat, long dry times, runs too hot, inconsistent temperatures
• A sticking thermostat may cause the high-limit safety to trip

• Disconnect power before servicing
• Access location varies by model; typically mounted on the blower or heater housing
• Move wires one at a time from the old thermostat to the new one; ensure tight, secure connections
• After replacement, clean the lint path and verify exterior venting for proper airflow

This thermal limiter is the dryer's high-limit thermostat. It monitors temperature and opens the heating circuit if the dryer overheats, helping protect components and allowing the appliance to operate safely.

• Provides over-temperature protection for the dryer's heating circuit
• Opens the circuit when excessive heat is detected to prevent damage
• If failed open, the dryer may run but not heat
• Repeated tripping can cause intermittent heat and longer dry times

• Disconnect power and allow the dryer to cool before servicing; shut off gas supply for gas models
• Handle wiring carefully; transfer leads one at a time and mount the limiter in the original location/orientation
• Use a multimeter to check continuity
• Clear lint buildup and prevent repeat overheating

A high-limit thermostat that stops the dryer's heating circuit if internal temperatures get too high, helping prevent overheating and protecting heating components. Replaces a failed high-limit thermostat to restore overheat protection. What it does

• Opens the heating circuit when dryer temperature exceeds the thermostat set point to prevent overheating.
• Commonly related symptoms: dryer runs but produces little or no heat, dryer gets unusually hot, or the thermal cutoff repeatedly fails.
• Works as part of the dryer's temperature-safety system to protect heating elements, fuses, and internal wiring.

• One high-limit thermostat

• Disconnect power before accessing the dryer and work only after panels are cool.
• Take a photo or label wires before removal to ensure correct reconnection.
• Test the thermostat for continuity with a multimeter to confirm failure before replacing.
• If other safety devices (thermal fuse, cycling thermostat, element) show symptoms, inspect and test those components too.

This time-delay fuse protects the appliance's power circuit by opening when current exceeds a safe level while tolerating brief inrush current. Replacing a blown fuse can help restore power once the root cause is corrected. What it does:

• Protects the line and control circuits from shorts and overloads
• Time-delay design helps prevent nuisance opening during startup surges
• When open, the unit will be completely dead—no display, lights, or response
• Repeatedly opening usually indicates an unresolved electrical fault that needs diagnosis

• 1 time-delay fuse

• Disconnect power at the breaker before servicing; some appliances can retain dangerous high voltage
• Replace only with the same type and rating specified by the manufacturer
• Inspect the fuse holder and wiring for heat damage or loose connections before reassembly
• If the new fuse opens immediately, stop and diagnose the underlying cause; never bypass or upsize a fuse

L290-40. 3 wire dryer thermostat.

This temperature control thermostat regulates your appliance's internal temperature by opening and closing the electrical circuit as conditions change, helping it reach and maintain the setting you select for consistent performance. What it does:

• Senses temperature and opens/closes contacts to control the system
• Helps maintain the set temperature by cycling the unit on and off
• Can lead to inconsistent temperature or a control knob that has no effect

• 1 temperature control thermostat

• Disconnect power before servicing; use proper PPE around sharp sheet metal
• Photograph wiring and transfer conductors one at a time to the new control
• Route it exactly as original and avoid kinks or sharp bends
• Set the control to mid-range after installation and allow the unit to stabilize before fine-tuning

This thermostat regulates your dryer's operating temperature for consistent, safe drying. The pink/white variant restores correct heat cycling when the original control fails, helping prevent overheating or underheating that leads to long dry times.

• Monitors dryer air temperature and opens/closes to control the heater or burner
• Helps maintain even drying performance and protect against overheating
• Failure symptoms can include runs too hot, takes too long to dry, no heat, or heat that won't shut off
• Color-coded pink/white version—use only the variant specified for your model

• Disconnect power (and gas, if applicable) and allow the dryer to cool before servicing
• Access the thermostat per your model's procedure; it is typically mounted to a housing surface for proper sensing
• Move wires one at a time to the new thermostat, matching positions as shown in the instruction sheet
• Reassemble, restore power, and run a test cycle to confirm proper heat cycling and airflow