Frigidaire Gasket & Seal

This seal kit includes the gaskets and sealing components that fit between the dishwasher tub and the outer cabinet. These seals prevent water from leaking out of the wash compartment during operation. Replace this kit if you notice water pooling underneath or around the sides of the dishwasher during a wash cycle.

Seals the blower housing to prevent air leaks and maintain efficient airflow. Replace if torn, damaged, or causing reduced drying performance.

Seals the air damper opening to maintain proper airflow between compartments. Replace if torn or compressed to fix uneven cooling and drafts.

Replace your range door gasket when it becomes worn, brittle, or deteriorated to restore proper heat containment and prevent leaks. Confirm fit with your model.

This replacement vent manages internal airflow within your appliance, routing air through the intended path. Restoring a damaged or missing vent helps maintain performance and reduces heat and moisture buildup inside the cabinet. What it does:

• Directs and regulates airflow through the appliance's air path
• Helps maintain proper pressure balance and efficient moisture removal
• Reduces the chance of lint or debris bypassing the intended ducting
• A cracked, warped, missing, or clogged vent can contribute to weak airflow, longer cycles, excess heat, or unusual noises

• 1 vent

• Disconnect power before servicing; allow hot components to cool
• Access the vent by removing the appropriate panel; note screw and clip locations
• Transfer any mounting hardware or seals from the old vent and ensure proper orientation
• Clear lint/debris from adjoining ducts before reassembly; test run to ensure smooth airflow and no rattling

Forms an airtight seal between freezer door and cabinet. Replace when worn or damaged to prevent warm air leaks, frost buildup, and temperature issues.

This is a rubber or foam gasket that seals around the electronic control board cover on the dishwasher door. It prevents moisture, steam, and detergent residue from reaching the control board electronics during wash cycles. Replace this gasket if you notice water damage to the control board, intermittent electronic failures, or if the gasket appears cracked, flattened, or missing.

H-shaped gasket seals evaporator housing to control airflow and reduce frost buildup. Replace if worn or cracked to restore cooling. Verify fit with model.

Seals the gap between burner and cooktop to prevent spills from leaking underneath. Replace when seal becomes discolored, cracked, or loses flexibility.

Seals between burner and cooktop to prevent spills and air leaks. Replace when cracked, hardened, or crumbling. Confirm fit with your model number.

This is a seal gasket that fits around the burner drip pan on a cooktop or range. It creates a tight seal between the drip pan and the cooktop surface to prevent spills and debris from falling beneath the burner area. Replace this gasket if it is cracked, hardened, or no longer sealing properly, which can allow grease and liquids to leak below the cooktop.

Seals the oven cavity to contain heat and prevent spills from leaking. Replace if cracked, torn, or no longer sealing properly. Verify fit with model.

Refrigerator freezer door gasket seals cold air inside. Replace if worn, torn, or allowing air leaks. Confirm fit with your model number before ordering.

This is a rubber lip seal that fits around the upper portion of the washer's basket drive tube, preventing water from leaking past the shaft and into the transmission or bearings below. It creates a watertight barrier between the wash tub and the drive mechanism. Replace this seal if you notice water leaking from beneath the washer tub, hear grinding noises during the spin cycle, or find oil residue under the machine.

Seals evaporator cover to direct airflow and prevent frost buildup. Replace if worn, cracked, or causing excess frost. Confirm fit with your model number.

This gasket seals the air duct between the freezer and refrigerator compartments, ensuring proper airflow distribution for consistent cooling. It creates an airtight seal around the duct opening to prevent cold air leaks and frost buildup. Replace this gasket if you notice frost forming around the air duct area, uneven temperatures between compartments, or if the gasket appears brittle, torn, or no longer seals properly.