Frigidaire Gasket & Seal

This H-shaped evaporator gasket creates a tight seal around the evaporator housing to help control airflow and reduce frost buildup in the freezer compartment. It replaces a worn or cracked gasket to restore proper cooling performance. What it does

• Seals the evaporator housing to prevent warm, moist air from entering the evaporator area.
• Helps maintain consistent airflow over the evaporator for efficient defrosting and cooling.
• Reduces frost and ice buildup caused by gaps or leaks around the evaporator.
• Commonly used when you see excessive frost, poor cooling, or visible gasket damage near the evaporator.

• One H-shaped evaporator gasket.

• Disconnect power to the appliance before starting any repair.
• Remove freezer panels and the evaporator cover to access the gasket; handle evaporator fins carefully to avoid damage.
• Clean mating surfaces and remove old adhesive or residue before installing the new gasket for a proper seal.
• If adhesive is required, use a refrigerator-safe sealant recommended by the manufacturer.

This O-ring is a small rubber seal that helps prevent water or refrigerant leaks by creating a tight connection between mating parts. Replacing a worn O-ring restores a secure seal and reduces dripping or loss of pressure. What it does:

• Forms a leak-tight seal at a joint or fitting to stop drips and seepage
• Helps maintain proper fluid or refrigerant pressure where used
• Commonly replaced when cracked, flattened, or hardened
• Can eliminate intermittent leaks that occur under load or when the appliance cycles

• Turn off and unplug the appliance and shut off water or refrigerant supply before service
• Inspect mating surfaces and replace any damaged fittings to ensure a proper seal
• Lightly lubricate the O-ring with appliance-safe silicone grease; avoid petroleum-based products
• Do not stretch or nick the O-ring during installation; confirm correct seating before restoring power or supply

This coil cover seal is a molded gasket that fits around the evaporator/coil cover to help keep airflow directed and reduce moisture and frost buildup. It restores the cover's sealing surface for more consistent cooling performance. What it does:

• Seals the evaporator/coil cover to help maintain proper airflow through the coil
• Helps reduce frost or ice buildup by keeping moist air away from cold coil surfaces
• Can prevent water dripping or pooling inside the cabinet near the coil
• Restores a tighter seal after a cracked, torn, or compressed gasket reduces effectiveness

• Disconnect power to the appliance before starting any repair
• You may need to remove the evaporator/coil cover or access panel to reach the seal
• Clean the mating surfaces and dry thoroughly before installing the new seal
• Handle the gasket gently and press evenly to seat; avoid stretching or sharp tools that could damage the part

This replacement door seal creates a tight perimeter seal to help keep conditioned air inside and reduce moisture or frost buildup. Fits factory specifications to restore proper sealing and improve efficiency. What it does

• Forms an airtight barrier around the door to limit air exchange and energy loss
• Helps prevent frost, condensation, and water pooling inside or under the appliance
• Reduces strain on the compressor by maintaining correct internal temperature
• Common symptom fix for visible gaps, torn or flattened gasket, or excessive frost buildup

• Seal as shown

• Disconnect power or unplug the appliance before starting any service
• Clean the door frame thoroughly before installing to ensure a good seal
• Work the gasket into the channel evenly; avoid overstretching or twisting
• If clips or retainer strips are present, follow OEM guidance for proper seating

This replacement door gasket seals the refrigerator compartment to keep cold air in and warm air out, helping maintain consistent temperatures and reduce energy use. It fits along the cabinet opening and forms the primary seal between door and cabinet. What it does:

• Creates an airtight seal to help maintain internal cooling and reduce compressor runtime
• Prevents warm, moist air from entering and causing frost build-up or condensation
• Helps keep food fresher by maintaining stable temperatures
• Common symptom: visible cracks, gaps, or torn edges around the door perimeter
• Common symptom: warm spots inside the fridge, excessive frost, or higher energy use

• Unplug or disconnect power to the appliance before starting any repair
• Remove the old gasket and clean the sealing surface thoroughly before installing the new gasket
• Some installations require basic hand tools; check the appliance's service guide for detailed steps
• If adhesive or clips are used, follow OEM instructions

This drain hose ring secures the washer's drain hose to the tub or drain outlet to help maintain a watertight connection and prevent leaks. It's a direct-fit replacement for the original ring used on compatible Frigidaire washers. What it does:

• Secures and seals the connection between the drain hose and the washer tub or standpipe
• Helps prevent water leaks at the hose connection point
• Keeps the drain hose properly positioned to ensure reliable drainage
• Useful when replacing a cracked, stretched, or missing hose ring

• Disconnect power and shut off the water supply before starting repair
• Drain any standing water from the washer before removing the hose
• Use pliers or a suitable hose clamp tool to remove and install the ring; avoid pinching the hose
• After installation, run a short cycle and inspect the connection for leaks

This O-ring seals the turbidity sensor assembly to help keep water contained and the sensor functioning properly. It's a small replacement seal for maintaining a watertight sensor connection and reliable turbidity readings. What it does:

• Seals the turbidity (water clarity) sensor housing to prevent leaks into the sensor area
• Helps maintain correct sensor operation so the control can monitor wash water clarity
• Restores a proper seal after sensor removal or repair

• Always disconnect power to the appliance before starting any repair.
• Remove the sensor assembly per manufacturer instructions; replace the old O-ring with the new one, ensuring it seats evenly in the groove.
• Inspect mating surfaces for nicks, debris, or old sealant and clean before installing the new O-ring.
• Use an appliance-safe lubricant compatible with rubber O-rings; avoid petroleum-based products unless specified.

This seal fits around the air diffuser to maintain a tight barrier and help direct airflow inside the appliance. It prevents air leaks and helps maintain even temperatures for better performance and efficiency. What it does:

• Creates a snug seal at the diffuser to reduce air bypass and uneven cooling
• Helps prevent excess moisture and frost buildup near the diffuser area
• Reduces drafts or weak airflow that can cause temperature inconsistency
• Helps minimize buzzing or vibration caused by loose diffuser fit

• Disconnect power to the appliance before beginning any work
• Remove the diffuser or access panel per your model's service instructions to reach the seal
• Press the seal into the diffuser channel, ensuring a full, even fit without gaps
• If the seal is brittle or torn, replace it to restore proper airflow control

This gasket is the refrigerator door seal that helps keep cold air inside and reduce energy loss. Replacing a worn or torn gasket restores a tight door seal for better cooling performance and food preservation. What it does:

• Seals the refrigerator door to maintain internal temperature and improve efficiency
• Prevents warm, moist air from entering which can cause frost, condensation, or temperature fluctuations
• Helps reduce compressor runtime by maintaining a consistent cabinet seal
• Restores proper door closing and reduces cold air leakage at the edges

• One refrigerator door gasket (single-piece seal)

• Inspect the door frame for damage and clean mounting surfaces before installing the new gasket
• Warm the gasket slightly with a hair dryer (low heat) to make installation and edge seating easier
• Align the gasket to the door channel and press evenly around the perimeter; some models require loosening the door for full access
• Disconnect power before working near electrical components