Frigidaire Refrigerator Parts

The Dispenser Module is an OEM part for Frigidaire refrigerators. It is a component located within the refrigerator door that is responsible for dispensing water and ice. The dispenser module houses the necessary valve assemblies, sensors, actuators and tubing required to deliver chilled water and ice on demand when the dispenser lever is engaged. It is designed to seamlessly integrate within the refrigerator door panel for convenient access.

Causes of a bad dispenser module can include buildup of mineral deposits or contaminants within the internal components that disrupt water flow or sensor functions over time. Mechanical wear and tear of plastic or rubber seals and valves is also common.

Symptoms of a bad dispenser module include:

• Slow or intermittent water flow from the dispenser
• Ice cubes dispensed one at a time instead of in batches
• Water or ice dispensing that doesn't work at all
• Leaks or water droplets below the dispenser area
• Error codes related to the dispenser on the control board

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Pan Crisper is an OEM part for Frigidaire refrigerators. It is a component located in the refrigerator door that allows for the storage of pans, baked goods, and other dishes in a humid environment to keep them crisp and fresh. The pan crisper features adjustable wire shelves and humidity control to optimize the storage environment. 

Causes of a bad pan crisper can include warping or bending of the shelves over time, cracking or damage to the humid pan located at the bottom, or failure of the humidity control mechanism.  

Symptoms of a bad pan crisper include:

• Loss of humidity within the crisper drawer
• Shelves that no longer sit level
• Inability to control moisture levels
• Warped or broken shelves

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. Replace yours today and restore optimum storage for baked goods in your refrigerator.
 

This is an ice bin that is used on refrigerator and freezer units. The purpose of this part is to store the ice that has already been made so that it is ready for dispensing. The auger is included with this part, which is the component that drives the ice out of the freezer for dispensing. Over time, the white plastic material that the bin is made of may begin to crack or break due to exposure to extreme temperatures over time. If this is the case, it will need to be replaced. If the auger no longer functions, it could have become damaged and this part will also replace the auger itself. Wear work gloves when replacing this part.This ice bin is compatible with refrigerator and freezer units that have been manufactured by Kenmore Elite, Kenmore Pro, Kenmore, and Frigidaire. It is sold individually. This part is sourced directly from the manufacturer.

The Crisper Drawer is an OEM part for Frigidaire refrigerators. It provides humidity-controlled storage for fruits and vegetables in the refrigerator compartment. The crisper drawer sits on a set of smooth-gliding rollers for easy access.

Causes of a bad crisper drawer can include cracked or broken plastic, rollers that no longer function properly, or issues with the sealing gasket.

Symptoms of a bad crisper drawer include:

• Difficulty opening and closing the drawer
• Excess moisture or drying out of stored items
• Warping or discoloration of the plastic structure
• Inability to regulate humidity inside the drawer

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The LED Light Bulb is an OEM part for Frigidaire refrigerators. It provides illumination inside the refrigerator and freezer compartments, making it easier to see and organize food items. This energy-efficient LED bulb ensures bright, long-lasting light with minimal energy consumption.

Causes of a bad LED light bulb can include electrical issues such as power surges, wear and tear over time, or damage due to impact or moisture exposure.

Symptoms of a bad LED Light Bulb include:

• The light not turning on
• Flickering or dim light
• Intermittent lighting issues
• Discoloration or reduced brightness

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Water Inlet Valve is an OEM part for Frigidaire refrigerators. It controls the flow of water into the refrigerator's ice maker and water dispenser, ensuring a steady and reliable water supply. This valve opens and closes as needed, allowing water to enter the ice maker and dispenser for proper operation.

Causes of a bad water inlet valve can include mineral buildup, wear and tear, or electrical issues. A malfunctioning valve can lead to problems with water flow, affecting the refrigerator’s ability to produce ice and dispense water properly.

Symptoms of a bad water inlet valve include:

• No water dispensing from the refrigerator
• Ice maker not producing ice
• Leaks from the valve area
• Unusual noises coming from the valve

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Defrost Heater Kit is an OEM part for Frigidaire refrigerators. This part is responsible for melting frost and ice buildup on the evaporator coils during the defrost cycle.  

Causes of a bad defrost heater can include regular wear and tear, electrical issues, or physical damage.  

Symptoms of a bad defrost heater include:

• Excessive frost or ice buildup in the freezer
• The refrigerator or freezer not cooling properly
• The defrost cycle not initiating
• Water leaking inside the refrigerator due to melting ice

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This white door gasket seals the perimeter of the refrigerator door. It helps keep cold air in and humid air out, supporting stable temperatures and reducing frost and moisture around the door opening. What it does:

• Maintains an airtight seal between the door and cabinet
• Replaces a torn, cracked, shrunken, or deformed gasket that won't seal
• Helps address condensation around the door, frost/ice buildup, temperature fluctuations, or a door that won't close flush

• 1 door gasket (white)

• Unplug the appliance before servicing
• Warm the new gasket (soak in warm water or use low, indirect heat) to relax kinks for easier fit
• Start at the corners and work evenly around the door; on screw-retained liners, loosen screws, seat the gasket lip, then retighten
• Close the door and check the seal; smooth out waves and allow the gasket to conform over the next 24 hours

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This replacement door gasket fits the refrigerator compartment. It forms a tight seal between the door and cabinet to help keep cold air in, limit moisture at the door, and maintain consistent temperatures. What it does:

• Seals the fresh food door opening to prevent air leaks
• Helps maintain stable interior temperature and humidity
• Reduces condensation and frost around the door perimeter
• Common failure signs: torn, warped, or compressed gasket; door not sealing; persistent condensation; temperature fluctuations; longer run times

• 1 refrigerator fresh food door gasket

• Disconnect power before servicing
• Lay the gasket flat to relax; gently warm with hot water or low heat to remove kinks
• Remove the old gasket; on many models, lift the liner lip or loosen retainer screws to release it
• Press the new gasket fully into the channel; check corners for a uniform seal and adjust door alignment if needed

The Kickplate Grille is an OEM part for Frigidaire refrigerators. It is a decorative and functional panel located at the base of the refrigerator, designed to provide ventilation and airflow access to the compressor and condenser coils behind it.

Causes of a damaged Kickplate Grille can include dents or physical impacts from objects striking the base, discoloration or warping from heat exposure, and general wear over time.

Symptoms that may indicate a need to replace the Kickplate Grille include:

• Visible cracks, dents, or other damage
• Restricted or blocked airflow, leading to poor ventilation
• Difficulty removing or reinstalling the grille panel properly
• Discoloration or fading that clashes with the appliance's aesthetic

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Door Shelf Support is an OEM part for Frigidaire refrigerators. This part supports the door shelf, providing a sturdy base to hold various items such as bottles, jars, and condiments securely in place on the refrigerator door.

Common causes of a bad door shelf support include regular wear and tear, overloading the shelf with heavy items, or accidental damage. 

Symptoms of a bad door shelf support include:

• The door shelf sagging or tilting
• Items falling off the shelf
• The shelf not staying securely in place
• Visible cracks or breakage in the support

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Crisper Pan is an OEM part for Frigidaire refrigerators featuring interior crisper drawers. It functions as a durable liner tray optimized to maintain proper humidity levels for storing fruits and vegetables. 

Symptoms of needing replacement include:

• Excessive cracking, pitting or peeling of surfaces   
• Sharp edges or broken corners become a hazard
• Difficulty fitting properly or staying securely in a drawer
• Inability to retain moisture or prevent drying out of foods

Causes can include heavy usage wear over time, being damaged during cleaning, or warping from extended high-humidity environments. 

This genuine OEM crisper pan is compatible with Electrolux, Gibson, Kelvinator, and Kenmore fridge models. 

The Power Cord is an OEM part for Frigidaire refrigerators. It transmits electrical current from the wall outlet directly to the internal refrigerator components, allowing them to operate properly. As the critical link supplying energy, this power cord plays an essential role in refrigerator performance.

Causes can involve normal wear over many years, accidental punctures, harsh chemicals, or excessive bending/pulling that strains and weakens internal wiring. Rodent damage is another potential issue.

Symptoms of a bad power cord include:

• The refrigerator not powering on when plugged in
• Flickering lights or intermittent operation
• Warm temperatures inside the fridge compartment
• Evidence of cord damage like cracks, blisters, or exposed wires

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Flipper Mullion is an OEM part for Frigidaire refrigerators. As the panel separating the fresh food and freezer compartments, it flips up for access while also providing an insulating barrier. 

Causes can range from normal wear and tear on hinge mechanisms to cracks or breaks from accidental impacts over years of use.

Symptoms of a bad flipper mullion include:

• Difficulty or resistance when trying to open
• Improper sealing between compartments, leading to air and temperature leaks
• Visible wear, cracks or damage to the component over time

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This bearing installs in the refrigerator/freezer door hinge to provide a smooth pivot point and maintain alignment. Replacing a worn bearing restores easy door movement and helps the door close and seal correctly.

• Provides a low-friction surface between the hinge pin and hinge bracket for smooth door pivoting
• Helps maintain proper door height and alignment for a reliable gasket seal
• Typical symptoms of wear: squeaking or grinding when opening, door binding or dropping, door not closing fully or popping open
• Excess wear can contribute to air leaks and frost buildup around the door

• Disconnect power before servicing; remove or secure items in the door
• Support the door; remove hinge fasteners and lift the door off if required
• Note and retain any shims/spacers; install the new bearing in the hinge as oriented in the diagram
• Reinstall and align the door; verify smooth operation and a complete gasket seal. Do not lubricate unless specified by the manufacturer