Frigidaire Screws, Nuts, Washers

This is a painted 1/4-20 machine screw used to secure appliance panels and components, restoring proper fit and stopping movement. It replaces small hardware lost or worn during repairs. What it does:

• Fastens panels, brackets, or assemblies with a 1/4-20 threaded hole
• Helps stop rattling, vibration, or loose-fitting parts
• Restores secure mounting after service or part replacement
• Matches finish to keep visible areas looking consistent

• Disconnect power and move the appliance to a safe, stable work area before servicing
• Use the matching screwdriver or socket; install by hand first to avoid cross-threading
• Tighten until snug—do not overtighten to prevent stripped threads or damaged parts
• Replace with the same size and finish screw; inspect threads before forcing

Mounting screw for laundry center units. Secures internal components and panels. Replace if stripped, missing, or damaged during disassembly or repairs.

This is a replacement screw used to secure components and panels on compatible appliance models. It provides a reliable fastening solution when original fasteners are missing, stripped, or damaged. What it does:

• Secures panels, brackets, or small appliance components in place
• Restores proper fit and alignment where a missing or damaged screw causes rattling or loose parts
• Matches OEM thread/form for a correct fit when replacing the original fastener
• Safe, direct replacement when the original screw is lost or worn

• Use the correct driver bit to avoid stripping the screw head
• Do not overtighten; snug to secure parts without distorting components
• Disconnect power and remove power supply or batteries as applicable before beginning repairs
• If replacing multiple fasteners, verify all are the same type and length before installation

This washer is a small hardware spacer that helps secure fasteners and maintain correct clearances in appliance assemblies. It prevents bolts and screws from loosening and keeps parts aligned for reliable operation. What it does:

• Provides a stable bearing surface between fasteners and mating parts to reduce wear
• Helps maintain proper spacing and alignment of panels, brackets, and components
• Reduces vibration-related loosening that can cause rattling or misalignment
• Common repair for loose or wobbly assemblies and noisy panels

• Disconnect power to the appliance before starting any repair
• If the washer is part of a water or gas connection, turn off the supply first
• Use the correct fastener size and torque to avoid deformation or slippage
• Replace damaged or corroded washers with the exact OEM part for best fit

A replacement screw with an attached sealing washer used to secure appliance panels and components while providing a moisture-resistant seal. Restores proper fastening and helps prevent leaks or drafts where a sealed fastener is required. What it does

• Secures panels, brackets or components to the appliance chassis using an integrated sealing washer.
• Creates a compression seal to help resist moisture or liquid intrusion at the fastening point.
• Helps reduce vibration and rattling when used in place of a worn or missing sealed screw.
• Commonly used where a watertight or sealed connection is needed around a screw hole.

• One screw with attached sealing washer.

• Disconnect power and any water supply before working on the appliance.
• Use the correct screwdriver or bit to avoid stripping the screw head.
• Tighten until snug; avoid overtightening which can damage the washer or mating parts.

This #8-32 x 3/8" screw secures appliance panels, trim and components so parts stay aligned and stable during normal use. Its standard size fits threaded holes where a short machine screw is required. What it does:

• Fastens panels, brackets, control trim or small assemblies to the appliance frame
• Restores secure fit when original screws are missing, stripped, or loose
• Helps stop rattling, vibration, and misaligned parts caused by loose hardware

• Use the correct #2 Phillips or appropriate driver to avoid stripping the head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Replace damaged screws with the same size and thread to ensure a secure fit
• Disconnect power or follow appliance safety steps when accessing internal components

This lockwasher secures fasteners and helps keep appliance components from loosening during normal use, reducing rattles and intermittent connections. Use it to restore proper clamp tension where a split/retaining washer is required. What it does

• Provides a spring-like tension under a nut or screw to resist loosening from vibration
• Keeps panels, brackets, and small assemblies held firmly in place
• Common symptom: loose or vibrating trim, panels, or internal components
• Helps maintain reliable electrical or mechanical connections by preventing fastener back-off

• One lockwasher

• Disconnect power and water before servicing the appliance
• Use the correct-size fastener and seating surface; replace damaged screws or nuts when present
• Tighten to snug fit—do not over-torque, which can deform the washer