Frigidaire Screws, Nuts, Washers

This washer is a small hardware spacer that helps secure fasteners and maintain correct clearances in appliance assemblies. It prevents bolts and screws from loosening and keeps parts aligned for reliable operation. What it does:

• Provides a stable bearing surface between fasteners and mating parts to reduce wear
• Helps maintain proper spacing and alignment of panels, brackets, and components
• Reduces vibration-related loosening that can cause rattling or misalignment
• Common repair for loose or wobbly assemblies and noisy panels

• Disconnect power to the appliance before starting any repair
• If the washer is part of a water or gas connection, turn off the supply first
• Use the correct fastener size and torque to avoid deformation or slippage
• Replace damaged or corroded washers with the exact OEM part for best fit

A replacement screw with an attached sealing washer used to secure appliance panels and components while providing a moisture-resistant seal. Restores proper fastening and helps prevent leaks or drafts where a sealed fastener is required. What it does

• Secures panels, brackets or components to the appliance chassis using an integrated sealing washer.
• Creates a compression seal to help resist moisture or liquid intrusion at the fastening point.
• Helps reduce vibration and rattling when used in place of a worn or missing sealed screw.
• Commonly used where a watertight or sealed connection is needed around a screw hole.

• One screw with attached sealing washer.

• Disconnect power and any water supply before working on the appliance.
• Use the correct screwdriver or bit to avoid stripping the screw head.
• Tighten until snug; avoid overtightening which can damage the washer or mating parts.

This #8-32 x 3/8" screw secures appliance panels, trim and components so parts stay aligned and stable during normal use. Its standard size fits threaded holes where a short machine screw is required. What it does:

• Fastens panels, brackets, control trim or small assemblies to the appliance frame
• Restores secure fit when original screws are missing, stripped, or loose
• Helps stop rattling, vibration, and misaligned parts caused by loose hardware

• Use the correct #2 Phillips or appropriate driver to avoid stripping the head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Replace damaged screws with the same size and thread to ensure a secure fit
• Disconnect power or follow appliance safety steps when accessing internal components

This lockwasher secures fasteners and helps keep appliance components from loosening during normal use, reducing rattles and intermittent connections. Use it to restore proper clamp tension where a split/retaining washer is required. What it does

• Provides a spring-like tension under a nut or screw to resist loosening from vibration
• Keeps panels, brackets, and small assemblies held firmly in place
• Common symptom: loose or vibrating trim, panels, or internal components
• Helps maintain reliable electrical or mechanical connections by preventing fastener back-off

• One lockwasher

• Disconnect power and water before servicing the appliance
• Use the correct-size fastener and seating surface; replace damaged screws or nuts when present
• Tighten to snug fit—do not over-torque, which can deform the washer

A small top-panel screw used to secure the appliance's top or trim pieces so panels stay aligned and stable. Simple replacement for loose or missing fasteners to restore proper fit and reduce rattling or shifting. What it does:

• Fastens the top panel or trim to the appliance cabinet
• Keeps panels aligned to prevent gaps and reduce vibration noise
• Replaces stripped, missing, or rusted screws that cause loose fits
• Works with the original mounting hole and thread engagement

• Turn off power to the appliance and unplug before accessing panels
• Use the correct screwdriver or driver bit to avoid stripping the head
• Replace like-for-like: match screw length and thread to ensure secure fit
• If rust or thread damage is extensive, replace mating hardware or use a new captive fastener as needed

Serrated mounting screw for dishwasher panels and brackets. Replace if stripped, rusted, or missing to secure internal components properly.

This is a genuine replacement screw used to secure appliance components and panels, restoring proper fit and function. It's a simple, reliable fastener for repair and maintenance tasks. What it does:

• Secures panels, brackets, trim, or internal components to restore stable assembly
• Replaces a stripped, missing, or rusted screw that prevents proper fastening
• Helps eliminate rattles or loose parts caused by worn fasteners
• Works where the OEM-specified screw is required for correct fit

• Use the correct screwdriver or bit to avoid stripping the head
• Hand-start the screw to ensure correct alignment before tightening
• Tighten only until snug—do not over-torque to avoid damage
• Disconnect power to the appliance before accessing internal components