Frigidaire Switch

This micro switch detects door or lid position and tells the appliance when the door is closed so cycles can start or safety interlocks stay engaged. It restores reliable door sensing and helps prevent operation with the door open. What it does:

• Acts as a position sensor that completes or breaks the control circuit when the door/lid is closed or opened
• Keeps the appliance from starting or continuing a cycle if the door is open (safety interlock)
• Common symptom fix: appliance won't start, stops mid-cycle, or shows door-related error codes
• Small electrical switch designed to mount at the door latch or frame and connect to the appliance wiring harness

• Disconnect power (unplug or shut off breaker) before attempting service
• Access may require removing panels, trim, or the door latch assembly; keep track of screws and fasteners
• Observe wiring orientation and connector positions; replace exactly as removed or tag wires

Gas burner won't light or clicks but doesn't ignite? Replace the igniter switch to restore spark and reliable lighting. Simple 15-30 minute DIY fix.

Fixes burner that won't shut off or heat properly. This infinite switch controls cooktop element temperature. Moderately easy DIY repair.

Fix a gas burner that won't light with this cooktop igniter switch. Common solution for spark ignition failure. Moderate DIY difficulty level.

Range burner not heating or stuck on high? This infinite switch controls surface element temperature. Common repair for unresponsive controls.

This pressure switch monitors the water level inside the washer tub and signals the control board when the correct fill level has been reached. It connects to a small air hose that runs to the tub. Replace this switch if your washer overfills, underfills, does not fill at all, or fails to advance past the fill cycle.

This wiring harness routes power and signals between a refrigerator's control components and electrical devices, restoring reliable electrical connections for operation and controls. It replaces a damaged or broken harness to help regain normal appliance function. What it does:

• Connects control board, sensors, lights, and other electrical components to provide power and signal paths
• Replaces frayed, burnt, or damaged wiring that can cause intermittent or complete loss of function
• Helps resolve symptoms such as lights or dispenser not working, erratic controls, or failure of specific features tied to wiring
• Restores proper connector fit and secure electrical contacts when original harness pins or wires are compromised

• One wiring harness as shown

• Always disconnect power to the appliance before starting any repair
• Match connector shapes and wire colors to the original harness; route along original paths and secure with clips or ties
• Inspect mating connectors and control board terminals for damage before installing the new harness

Fix washer overfilling or incorrect water levels with a new pressure switch. Solves fill problems across load sizes. Most installs in 5-10 minutes.

Washer overfilling or running without water? Your pressure switch likely failed. This switch monitors water levels to prevent overflow problems.

This is a push-button style switch used in the cooktop burner ignition system. It activates the spark module to ignite the gas when a burner knob is pressed or turned. Replace this switch if a burner no longer sparks when you attempt to light it, or if the igniter clicks continuously without stopping.

A push-button switch that restores user control functions by completing or breaking electrical circuits. Replaces a worn or failed control switch to help restore normal operation and user input response. What it does:

• Acts as the user-operated control input to start or stop a function when pressed
• Opens or closes the electrical circuit that enables the associated control or feature
• Common symptom: unresponsive controls or functions that do not start when buttons are pressed
• May cause intermittent operation or no response if contacts are worn or corroded

• One replacement push-button switch

• Disconnect power to the appliance before attempting any service
• Use appropriate tools and basic electrical safety; avoid bending terminals or forcing the new part into place

Fix a microwave that won't start or stops running with a new door interlock switch. This safety component ensures proper door closure for operation.

This is a 7-position temperature selector switch that mounts on the washer's control panel and allows you to choose the water temperature for each wash cycle. It controls the mix of hot and cold water entering the tub. Replace this switch if your washer fills with the wrong water temperature, only uses hot or cold regardless of the setting, or if the temperature dial no longer clicks into position.

Fix a refrigerator dispenser that won't activate water or ice with this dispenser switch. Simple DIY repair taking 15-30 minutes with basic tools.