General Electric Cooktop Parts

Ordered new parts and replaced all. Had to slightly modify the wire terminals all four surface elements so that they would fit the ceramic insulators that were shipped with each one. Read more

I was getting really frustrated with our oven. It would preheat to the correct temperature, then slowly lose heat until it was down to about 200 degrees. So it took about two hours to heat a pizza! Finally decided to repair the oven myself, rather than pay $300.00 to have a repair person come out. Ordered the replacement igniter from AppliancePartsPros.com, and it arrived in two days. I followed the instructional video on the AppliancePartsPros.com website, and it was going well until I... Read more

Refer to Mynor T. of Draper, UT Aug. 12, 2018 write-up. I benefited greatly from the above write-up. It took me a little less time to perform this repair (excluding cleaning the assembly) due to the write-up. This GE Profile gas burner cook top is a “drop-in” model meant to be installed into counter top cut outs. The glass top edges are the actual support area for the entire cook top assembly. The burner bases (on top of the glass top) are screwed to the metal case enclosure (located beneath... Read more

I had to take the control board off the bottom of the cooktop and replace the fan switch. The post that fits into the hand switch had broken off. The new switch cost about $35, it was an exact replacement and the whole repair took less than an hour. My wife is very happy because now she can again use the downdraft fan on the cooktop. Thank you AppliancePartsPros. Read more

• Won't start

Did some research to find out it was the electrode. Pulled out the old one to match what was on your site. It came in no time at all, and the replacement was a cinch. Read more

Going on line and viewing your website, you provided a very easy way to get me to a picture that was exactly what I wanted with the exact (old style) connections. I had previously gone to Home Depot twice, and I still did not get the correct burner that I needed. Your website was great, I should have gone there first. I used the part that I received from AppliancePartsPROS.com and replaced the defective, old and non-working surface element. It was easy, I used a screw driver to snap off a... Read more

• Element will not heat

Ordered recommended part for GE appliance. Change was very simple. Followed instructions on video and removed one wire at a time. Very easy to change 5 to 10 minutes. Read more

Replaced spark module and all electrodes/igniters. Read more

• Element will not heat

Unplug range. Open oven door to gain access to the cook top lock-down screws, located under the front edge of the cook top. Tip the cook top up and carefully remove it by pulling forward. Set aside in a safe place. Remove old, burned-out, element by removing the single lock tab, located on one of the three mounting posts, then lift up. Leave the wiring attached. Flip the element over and remove the three mounting tabs, making note of their numbered locations. Transfer the mounting tabs to... Read more

• Element will not heat

Ordered new heating coils for stove Read more

While trying to fix the problem I broke the knob. Appliance Parts Pros.com had the part delivered in 2 days! After looking at the video I decided there was a poor ground at burner #1. Removal of burner confirmed my suspicion. Years of use “spills” has insulated the burner from a good ground, thus preventing a good spark. Removal of black residue cleared the problem. I am now in the process of cleaning the remaining 4 burners just to be sure. Read more

I first checked a repair video and found the procedure was a 10 minute job. I then went to the website, put in my stove model number and searched for the switch. While I was looking I was offered a chat session with one of their experts. I am glad that I accepted. The switch I was looking at was not the right switch for the job. My expert verified my model number and the switch that need to be replaced. After a couple of minutes, she came back with the right part and placed the order for... Read more

Removed the defective burner labeled the leads as to their location and coil connections. Replaced the connections to the corresponding locations, 1 to 1, 2 to 2 and the bridged terminal as it was. I noticed that the coils in the replacement burner were not wound in the same direction as the original burner and made note of this. I did not think much of this at the time, but on turning the power back on and lighting up the burners I noticed up they were not lighting up the corresponding... Read more

We had searched everywhere for replacement knobs on my cooktop. We had even ordered some from other vendors, but they were wrong. I found AppliancePartsPros.com and they had them and were able to deliver them within 3 days of my order. Read more

Each part came with a video - great site. Prices are reasonable and parts are OEM. Would use them again. Read more

Shut power off to unit. Took cook top out and removed metal cover to remove electrical board. Replaced with new one. Was just 5-6 connections that couldn’t be mixed up. Fairly easy fix. Works like new. Read more