General Electric Dryer Control Board

Fix a dryer that won't turn on or power up. This main power control board restores electrical functions. Moderate DIY repair for experienced users.

Fix a broken or stripped timer knob that won't turn or stay engaged. This plastic shaft restores the connection between knob and timer. Simple 5-minute fix.

Dryer won't shut off or timer won't advance? This mechanical timer controls cycle timing and program selections. Restores proper cycle operation.

This is a mechanical timer that controls the duration and sequence of drying cycles in your dryer. It advances through the selected cycle, activating the motor, heater, and cool-down periods at the appropriate times. Replace this timer if your dryer won't start, won't advance through cycles, runs continuously without shutting off, or stops mid-cycle.

Dryer shuts off after a few seconds or won't power on? Replace the main power control board to restore power distribution and control functions.

Dryer won't turn off or advance cycles? This mechanical timer controls cycle selection and transitions. Moderate DIY repair restores automatic shutoff.

Dryer won't start, won't heat, or displays errors? The main control board manages all dryer functions. Common fix for no-start and timing issues.

Dryer won't start or advance through cycles? This timer control regulates cycle timing and functions. Moderate DIY repair with basic tools.

Replace a faulty dryer timer when cycles won't advance, stop mid-cycle, or the timer knob doesn't turn. Restores proper cycle operation and timing.

This genuine replacement part is a user interface board for dryers. The user interface board is the circuit board that responds to the buttons located on the control panel allowing the user to adjust the dryer settings. If the dryer is no longer responding when buttons are being pressed then it might be time to replace the user interface board. Luckily this is a relatively easy repair.To replace the interface board begin by turning off the power to the dryer. Once the power has been shut off move the dryer away from the wall to gain access to the upper back panel. Remove the panel and locate the interface board. Snap it out of its brackets and remove the wire harness attached to the board. Reinsert the wire connector to the new interface and snap the new board assembly back to its original place.This OEM replacement part is sold individually and is compatible with General Electric, Hotpoint, and RCA brand Dryers.

Dryer won't advance through cycles or stops mid-cycle? This timer and wiring harness kit restores accurate cycle control. Moderate DIY repair.

Fix a dryer that won't start, advance, or complete cycles with this electromechanical timer. Controls cycle selection and timing. Moderate DIY repair.

Dryer won't start or has no power? This electronic control board manages dryer cycles and settings. Straightforward replacement restores function.

This electromechanical timer assembly controls cycle timing for compatible GE ranges and ovens, restoring accurate cook cycles and timer functions. It replaces a worn or non-advancing control to help your appliance complete timed operations reliably. What it does:

• Advances and times cooking cycles so bake, broil and self-clean operations run to completion
• Restores timer and manual cycle control when the original timer stops advancing
• Helps resolve symptoms like no timer display, oven cycles that won't start or stop on schedule, or intermittent timing failures
• Works as the user-accessible timing control for front-panel settings

• Disconnect power to the appliance before beginning service to avoid shock hazard
• Access may require removing the range/oven control panel or console; keep fasteners and trim for reassembly
• Handle connectors carefully and match wiring/location during reinstallation

Dryer skipping cycles or getting stuck? This timer control regulates cycle progression. Common repair when your dryer won't advance or complete cycles properly.

This display assembly powers and visually reports the appliance control status so you can see settings and feedback on the control panel. It restores readable on-screen information and enables the front-panel display functions. What it does:

• Replaces the control-panel LCD and power/display electronics so the screen lights and shows information again
• Commonly used when the display is blank, dim, flickering or showing garbled characters
• Resolves unresponsive or intermittent front-panel display behavior tied to the display module
• Interfaces with the main control board to present time, temperature, and mode/status readouts

• One complete display assembly (power/LCD) as shown

• Disconnect power to the appliance before beginning any work to avoid shock
• Handle the LCD and cable connectors carefully to avoid damage; flexing or scratches can affect operation
• Access typically requires removing the control console or console bezel—keep track of screws and fasteners
• If symptoms persist after replacement, test the main control board and wiring harness for faults