General Electric Refrigerator Parts

This defrost heater and thermostat assembly melts frost from the evaporator and shuts off at the proper temperature during the defrost cycle, restoring airflow and helping the refrigerator maintain steady, reliable cooling performance.

• Heats the evaporator to clear frost/ice during the automatic defrost cycle
• Thermostat opens to terminate heat once a safe temperature is reached
• Helps restore air circulation to the fresh food section
• Common failure signs: heavy frost on the freezer back wall/evaporator, poor cooling or warm fridge, fan noise from ice contact, little or no water in the drain pan after "defrosts"

• Disconnect power before service; work on a fully de-energized appliance
• Access is typically behind the freezer's rear panel; remove shelves/ice components as needed
• Fully defrost before installing the new assembly to prevent damage and ensure proper fit
• Reinstall in the original locations; clamp the thermostat to the evaporator tubing and route wiring exactly as factory, away from sharp edges and moving parts

This left side snack pan slide is a genuine General Electric part, sold individually. This left side snack pan slide can be used as a replacement part for a refrigerator. This is the part on which the crisper drawer rests, and it facilitates the sliding in and out of the crisper drawer. The left side snack pan slide is made out of durable white plastic.The left side snack pan slide might have to be replaced at some point within the lifespan of a refrigerator if it is damaged to the point that it can no longer serve its function. This damage could take the form of cracks, punctures, or erosion to the plastic material as a result of general wear and tear or from a collision with a hard object that warps the component beyond functionality. If either of these things occur, the component should be removed and replaced with this genuine OEM replacement part.This is an OEM part sourced directly from the manufacturer. It is sold individually. This left side snack pan slide is compatible with the following appliance brands: General Electric and Kenmore.

The Freezer Door Lower Hinge Bushing is an OEM replacement part for GE refrigerators. It is a component located within the freezer door hinge.

Causes of failure typically involve normal wear over extended use. Refrigerator doors experience frequent adjustment which can deteriorate hinge bushings.

Symptoms of a bad lower hinge bushing include:

• The freezer door being loose or wobbly in its closed position
• Excessive noise, grinding, or vibration coming from the door hinge area
• Difficulty smoothly opening or closing the door

This is a genuine OEM part that works for some models of GE, and Hotpoint models.

The Shelf is an OEM part for GE refrigerators. It provides a stable and durable surface for storing food and other items within the refrigerator. The shelf is designed to fit seamlessly into the refrigerator's interior, maximizing space and organization. It measures approximately 25 inches wide by 14 inches deep.

Over time, the shelf can become damaged due to heavy loads, accidental impacts, or regular wear and tear. If you notice cracks, chips, or instability in the shelf, it is important to replace it to ensure safe and effective storage.

Symptoms of a bad shelf include:

• Cracks or visible damage
• Difficulty in keeping items stable
• Reduced storage capacity due to instability

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This freezer shelf trim snaps onto the shelf edge to secure the liner/glass and provide a clean front lip in the freezer compartment. Replace a broken or missing trim to restore shelf stability and help keep items in place.

• Attaches to the shelf edge to finish the front and retain the shelf/glass panel
• Helps stabilize the shelf and prevent items from slipping forward
• Common failure signs: cracked, warped, or missing trim; loose shelf edge or shifting glass
• Restores original fit and appearance

• Unplug the refrigerator and remove items from the affected shelf
• Lift out the shelf assembly; handle any glass carefully
• Release the old trim from the tabs and snap the new trim onto the shelf edge evenly
• Allow cold plastic to warm to room temperature to reduce the chance of cracking

Refrigerator crisper drawer that serves as the vegetable pan. It holds produce in the crisper section and slides on the rails to keep items contained and organized. Replace cracked or missing bins to restore smooth access and storage. What it does:

• Contains fruits and vegetables in the crisper area beneath the cover
• Works with the crisper cover/humidity controls to help manage moisture
• Slides on the frame rails for easy, smooth access when intact
• Replace if cracked, broken, warped, or if it won't stay on its tracks

• 1 vegetable pan (crisper drawer)

• Unplug the refrigerator before servicing interior parts
• Remove the crisper cover or shelf if needed; pull the old pan straight out
• Clean and inspect the rails; align and slide the new pan fully onto the tracks
• Do not force or overload the drawer; verify smooth travel

The Defrost Timer is an OEM replacement part for GE refrigerators. It automatically initiates timed defrost cycles to prevent the buildup of frost or ice within the refrigerator compartment and freezer coils. Regular defrosting maintains optimal temperature regulation and airflow while minimizing mineral deposits long-term.  

Symptoms of a bad defrost timer include:

• Inability to initiate automatic defrost functions
• Accumulation of excessive frost or ice buildup risking freezer damage    
• Temperature control or airflow issues disrupting refrigeration  
• Potential dripping or leaks from defrost water overflow

Causes of failure involve worn-out internal contacts or degraded electronic components from extended exposure to refrigerated conditions. Mineral residue accumulating within the timer mechanism over many years also risks impeding electrical connections.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore refrigerators. 

This rear gasket fits the refrigerator's crisper cover, sealing the back edge of the glass/frame. It helps maintain proper airflow and humidity in the crisper area while cushioning the glass and reducing rattles and gaps.

• Creates a seal along the rear edge of the crisper cover to limit air leaks
• Helps maintain consistent humidity and airflow in the crisper compartment
• Cushions and supports the glass to minimize vibration and noise
• Replace if torn, flattened, missing, or if you see gaps or glass rattle

• Unplug the refrigerator before servicing
• Remove crisper drawers and carefully lift off the glass cover/frame
• Pull the old gasket from the rear channel and clean the mating surfaces
• Press the new gasket fully into the rear channel; reinstall cover and drawers, checking for an even seal

This gasket and label assembly is used on side-by-side refrigerators to restore a proper seal at the specified location and provide the matching identification decal. A tight seal helps keep cold air in, moisture out, and performance consistent.

• Creates an air-tight seal between mating refrigerator parts or panels
• Helps maintain stable temperatures and reduce frost/condensation
• Replace if the gasket is torn, deformed, brittle, or missing
• Helps address sweating around edges, warm spots, or longer run times

• Disconnect power before servicing; turn off water supply if working near water components
• Remove the old gasket/label and clean/dry the surfaces thoroughly
• Seat the gasket evenly without twists; ensure full contact all around
• Apply the label in the specified location per your model's documentation

This replacement door shelf bin mounts inside the fresh food door to provide adjustable storage for condiments, jars, and bottles. Restore secure, organized space when the original bin is cracked, loose, or missing. What it does:

• Attaches to the fresh food door rails and can be repositioned to different slots for adjustable storage
• Holds jars, condiments, and small bottles securely on the door
• Helps prevent items from tipping or falling during door movement
• Replaces a cracked, broken, or missing bin to restore usable capacity

• 1 fresh food door shelf bin

• Disconnect power or switch the refrigerator off; remove items from the door area
• Lift the old bin straight up to release it from the door slots
• Align the new bin with the desired slots and press down until fully seated and secure
• Verify the bin is level and the door closes and seals properly

The Freezer Shelf is an OEM part for GE refrigerators. This shelf provides additional storage space within the freezer compartment, allowing you to organize and store food items more efficiently.

Causes of a bad freezer shelf can include regular wear and tear, damage from heavy or improperly placed items, or cracking from exposure to extreme temperatures.  

Symptoms of a bad freezer shelf include:

• Cracks or breaks in the shelf
• The shelf not fitting properly into the designated slots
• Difficulty in securing the shelf in place
• Reduced storage capacity due to damage

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Main Control Board Assembly is an OEM part for GE refrigerators. This part manages and regulates various functions of the refrigerator, including temperature control, defrost cycles, and the operation of the compressor and fans.

Causes of a bad main control board can include electrical surges, overheating, or component failures due to age or manufacturing defects. 

Symptoms of a bad main control board include:

• Refrigerator not cooling properly
• Erratic temperature fluctuations
• Unresponsive control panel
• Frequent cycling on and off
• Unusual noises from the refrigerator

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Gasket Evaporator Cover is an OEM part for GE refrigerators. This part seals the evaporator cover, ensuring that cold air does not escape and that the refrigerator operates efficiently. 

Causes of a bad Gasket Evaporator Cover can include wear and tear over time, exposure to extreme temperatures that degrade the material, or physical damage that breaks the seal.  

Symptoms of a bad Gasket Evaporator Cover include:

• Noticeable frost buildup in the freezer compartment
• The refrigerator runs more frequently or for longer periods
• An increase in energy consumption
• Difficulty maintaining consistent temperatures within the refrigerator

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Ice Crusher Housing is an OEM part for GE refrigerators. This part provies a protective enclosure that ensures the ice is crushed efficiently and safely before being dispensed.

Causes of a bad ice crusher housing can include wear and tear from regular use, damage from ice jams or foreign objects, and exposure to temperature fluctuations.  

Symptoms of a bad ice crusher housing include:

• Ice not being crushed properly
• Ice jams or blockages in the dispenser
• Leaks or cracks in the housing
• Unusual noises during the ice crushing process

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Control Board Assembly is an OEM part for GE refrigerators. This part manages and coordinates various functions of the refrigerator, such as temperature regulation, defrost cycles, and the operation of the compressor and fans.

Causes of a bad control board assembly can include electrical surges, wear and tear over time, or damage from moisture and condensation. 

Symptoms of a bad control board assembly include:

• Inconsistent temperature regulation
• The refrigerator not cooling or freezing properly
• Error codes or display malfunctions
• Unusual noises from the refrigerator

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Temperature Sensor Grille is an OEM part for GE refrigerators. This grille covers and protects the temperature sensor, ensuring it accurately measures the internal temperature of the refrigerator.  

Causes of a bad grille can include physical damage from impacts, regular wear and tear, or the buildup of dust and debris that can obstruct airflow.  

Symptoms of a bad temperature sensor grille include:

• Inaccurate temperature readings
• The refrigerator running continuously or not cooling properly
• Visible damage or obstruction on the grille
• The sensor becoming loose or dislodged

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.