General Electric Refrigerator Parts

The Veggie Pan Drawer is an OEM replacement part for GE refrigerator models. It is located below the main fresh food storage shelves, this enclosed space utilizes an evaporative system to humidify stored produce.

Causes of failure typically involve excess mineral buildup clogging the humidity mechanism over several years of use. Introducing too much water can also damage electronic components.

Symptoms to watch for include:

• Interior pan cracking or tiles crumbling from over-saturation
• Drawer failing to maintain proper humidity levels  
• Premature spoiling of fruits and veggies lacking consistent moisture

This OEM GE part is compatible with Profile models as well as some Kenmore refrigerators. 

This evaporator fan motor dust cap is an authentic OEM replacement part found on refrigerator and freezer fan motors. This dust cap prevents the fan motor bearing and housing from being damaged by dirt and debris. If the dust cap is cracked or broken, the fan may make loud squealing noises. If the dust cap is not removed and replaced, the fan could stop working and ultimately cause the refrigerator's temperature to be affected. To start, disconnect the power and water to the refrigerator. Remove food from the freezer so that the back panel of the freezer can be accessed to reach the fan. Remove the ice maker and set it outside the freezer. Disconnect the fan and take it out of the freezer to expose the fan's shaft and the dust cover. Pry the dust cover off and install the new one. Replace the fan and cover. Reconnect the wires and reinstall the icemaker. Put the food back in the freezer. Reconnect the power and water.The evaporator fan motor dust cap is a white plastic part that is sold individually. This dust cover is made for use in refrigerators manufactured by General Electric, Hotpoint, and Kenmore.

The Heater Defrost Assembly is an OEM part for GE refrigerators. This part melts any frost or ice that accumulates on the evaporator coils, ensuring efficient cooling and preventing frost buildup that can impede airflow.

Causes of a bad heater defrost assembly can include electrical failures, wear and tear over time, or damage from fluctuating temperatures.  

Symptoms of a bad heater defrost assembly include:

• Excess frost buildup on the evaporator coils
• The refrigerator not cooling properly
• Water leaking inside the refrigerator
• The defrost cycle not activating

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Main Control Board Assembly is an OEM replacement part for GE refrigerators. It is an electronic component located on the back of the refrigerator that is responsible for monitoring and controlling various refrigerator functions. The main control board regulates temperatures, fresh food and freezer compartment levels, defrost cycles, ice production, and more.

Causes of a bad main control board can include short circuits, malfunctions in electronic components over time, damage from moisture or impacts, or incompatible replacement parts used previously.

Symptoms of a bad main control board include:

• The refrigerator not cooling/freezing properly
• Issues maintaining set temperatures
• Error codes displaying
• Control pads/buttons not functioning
• Abnormal noises from inside the appliance

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Water Valve and Bracket Kit is an OEM part for GE refrigerators. It includes a water valve and a mounting bracket designed to facilitate the connection and operation of your refrigerator's ice maker and water dispenser system. This part controls the flow of water into the refrigerator, ensuring that both the ice maker and water dispenser receive the proper amount of water at the correct pressure.

Causes of a bad Water Valve and Bracket Kit can include mineral deposits from hard water, which can clog or damage the valve, and normal wear that might cause the valve to leak or fail to open or close properly.

Symptoms of a bad Water Valve and Bracket Kit include:

• No water output from the dispenser
• Slow or no ice production
• Water leakage around the refrigerator

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Color: white

The Screw is an OEM part for GE refrigerators. It serves a crucial function in securing and allowing smooth operation of the refrigerator's drawer rollers.

Causes of a bad or missing screw can include accidental loss during repair or maintenance, stripping of the screw threads due to overtightening, or general wear and tear over time.

Symptoms of a loose or screw include:

• Loose or wobbly refrigerator drawer
• Difficulty opening or closing the drawer smoothly
• Scraping or grinding noises when operating the drawer
• Drawer coming off the track or rollers entirely

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Replace a cracked or jammed ice bin with this bucket and auger assembly. It stores the ice and uses the auger to move it toward the dispenser chute, restoring smooth, reliable through-the-door ice dispensing.

• Holds harvested ice in the freezer compartment
• Auger engages the drive to move ice toward the dispenser chute
• Helps restore consistent ice delivery through the door
• Typical symptoms: no ice dispensing, weak or intermittent dispense, cracked/broken bucket, grinding or clicking during dispense

• Unplug the refrigerator before servicing
• Empty the old bin and pull the assembly straight out
• Align the rear auger coupling with the drive and seat the assembly fully
• Briefly test the dispenser to confirm proper auger engagement

This deep fresh food door bin installs on the right-hand refrigerator door to provide sturdy storage for taller containers and everyday items. Replace a broken or missing bin to restore safe, organized space on your refrigerator door.

• Mounts to the right-side fresh food door to hold and organize items
• Deep profile adds capacity for taller containers and bottles
• Replace when the bin is cracked, warped, has broken tabs, or won't stay seated
• Common symptoms: bin falls out, leans, is loose, or is missing

• Empty the old bin; lift straight up to remove from the door liner
• Align the new bin's hooks with the slots and press down until fully seated
• Handle gently; allow plastic to warm to room temperature to reduce cracking risk
• Do not force into place; ensure correct right-side orientation

The Freezer Shelf is an OEM replacement part for GE freezers. This shelf provides storage throughout the freezer compartment. It measures approximately. 25" x 12".

Causes of a bad freezer shelf can include cracked or broken steel from overloading, corrosion from moisture exposure over years of use, or damage from impact.

Symptoms of a faulty shelf include:

• Visible cracks, breaks, or fractures in the steel
• Shelves that cannot adequately bear the weight of frozen items
• Missing or detached shelf mounting fasteners
• Sharp edges or projections creating a safety concern

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Snack Pan Slide is an OEM part for GE refrigerators. This part provides a smooth track for the snack pan or deli drawer to slide in and out, ensuring easy access to stored items.

Causes of a bad snack pan slide can include regular wear and tear, damage from overloading the drawer, or breakage due to improper handling.  

Symptoms of a bad snack pan slide include:

• Difficulty opening or closing the snack pan
• The snack pan not sliding smoothly or getting stuck
• Visible cracks or damage to the slide
• The snack pan not staying aligned or securely in place

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This helix is the plastic spiral inside the refrigerator's ice bucket that works with the auger to move ice toward the crusher and dispenser. Replacing a worn or broken helix restores smooth ice dispensing and reduces jams.

• Surrounds the auger shaft in the ice bucket to advance cubes toward the crusher/chute
• Engages when the dispenser is activated to feed ice consistently
• Replace if cracked, stripped, or warped
• Symptoms may include little or no ice dispensing, intermittent dispensing, or grinding noises from the bucket

• Unplug the refrigerator and wear cut-resistant gloves; crusher blades are sharp
• Remove and empty the ice bucket; note the order/orientation of blades, spacers, and washers during disassembly
• Transfer components to the new helix in the same sequence; reuse existing hardware
• After reassembly, verify the auger turns smoothly by hand before reinstalling and testing

The Ice Bucket and Auger Assembly is an OEM part for GE refrigerators. This part stores ice and includes an auger mechanism that helps dispense the ice through the refrigerator's ice dispenser.  

Causes of a bad ice bucket and auger assembly include cracks in the bucket, worn or broken auger blades, or issues with the auger motor.

Symptoms of a bad ice bucket and auger assembly include:

• Ice not dispensing properly or at all
• Unusual noises when the dispenser is activated
• Visible damage to the bucket or auger
• Ice clumping or jamming in the bucket

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Dispenser Touchpad is an OEM part for GE refrigerators. This touchpad allows users to control the dispensing of water and ice from the refrigerator by selecting options and settings on the interface.

Causes of a bad touchpad can include electrical failures, wear and tear from regular use, or damage from moisture and spills. 

Symptoms of a bad dispenser touchpad include:

• Unresponsive or intermittent touch controls
• Incorrect or erratic dispensing of water or ice
• Display issues or malfunctioning lights
• Difficulty selecting or changing settings

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Gasket is an OEM part for GE refrigerators, specifically designed to ensure an airtight seal around the refrigerator or freezer door. This crucial component plays a significant role in maintaining the appliance's energy efficiency by preventing cold air from escaping and warm air from entering. 

Causes of a bad Gasket can stem from normal wear and tear over time, accidental damage, or deformation due to improper cleaning methods or exposure to extreme temperatures. 

Symptoms of a bad Gasket include:

• Visible gaps or tears in the gasket material
• Condensation or frost buildup inside the refrigerator or freezer, indicating air leaks
• Difficulty in maintaining consistent internal temperatures
• An increase in energy consumption as the appliance works harder to maintain the desired temperature

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Ice Chute Funnel is an OEM part for GE refrigerators. It directs ice from the dispenser to the glass. 

Causes of a bad ice chute funnel can include wear and tear over time, cracking or breaking due to frequent use, or damage from attempting to clear jams or blockages.  

Symptoms of a bad ice chute funnel include:

• Ice spilling or missing the glass during dispensing
• Difficulty in dispensing ice or frequent jams
• Cracks or visible damage to the funnel
• Ice buildup or blockages in the dispenser chute

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.