Hotpoint Parts

Replacement of the evaporator fan motor, fan blade, and grommets. The amount of disassembly to reach the part took most of the effort Read more

• Won't start
• Noisy
• Will not drain

I fixed it by installing a ge pump and motor assembly. it works fine Read more

• Freezer too cold
• Fridge too cold
• Too warm
• Freezer section too warm

Yes, a 49-yr old woman fixed this fridge all by herself! AppliancePartsPros was very helpful in the diagnosis of the problem, which I determined to likely be the result of defrost failure. There was a large amount of ice and frost coating the back of the freezer despite the inside temp being 42 degrees. My husband thought I was crazy to think it was a problem with ice when the temperature was warm, but I told him to trust me and I would attempt the repair. He just wanted to throw the old one... Read more

I replaced all 3 remaining burner controls because they were all original (mid 1970s GE electric range w/coil burners), and one of the controls occasionally made arcing sounds when cycling the burner on and off. If a control is making odd noises - more than just a quiet metallic clicking as it cycles - it should be replaced. I'm assuming you have experience with the tools needed and can do simple mechanical assembly or disassembly, but have not previously worked with electrical equipment of... Read more

Before buying a new ($1200) washer, I found the trouble shooting guide and decided to check if my problem was a simple fix or a complicated procedure... turns out it was the simple fix. Removing the agitator was the hardest part, it lifted straight up, but took some muscle and a belt for leverage. Then I had to remove one bolt, lift off the damaged part, and put the new part on with the one bolt. Done. Works perfectly. Read more

• Fridge runs too long
• Door won't open or close
• Door sweating

I followed the directions on the video.....had to look at it a couple of time. Difficult to work lying on the floor for me, but the technique was spot on. I have now replace the door closing cams on the refrigerator door and the freezer door of the side by side unit. Thanks for such great instructions. Read more

The start button broke?!? I ordered another start button and it looked exactly like the one I had. I figured it would break as well, so I might as well try to fix the broken one. I unplugged the power, removed the back of the dryer console, disconnected the start switch from the button and the dryer, depressed the 3 pop out tabs to remove the button from the dryer. I put the switch back in place and reinstalled the back. I clipped off the 3 projections that kept the button from being... Read more

The repair went great with the guidance from your website and the parts that we purchased! also the video was great! Read more

Went ahead and replaced the pulley as well the drum bearing sleeve and O ring, drum belt and the front drum bearing slides. Put the unit back together and she ran like a top! Read more

My refrigerator is 13 yrs old and began to build up frost in the ice cube shoot and the water tube began to freeze up over night. The flapper door was not closing completely. I simply removed the control panel by pulling up and out on the bottom edge, the edge is only about 1/8 inch thick, so don't reach in to far. You should be able to feel a small division line between the control panel and the refrigerator. No screw driver was needed to expose the 4 mounting screws of the inner dispenser... Read more

Ordered replacement which was a perfect fit. Read more

Bought and installed bumpers Read more

Replaced door strike and door latch Read more

• Ice maker dispenses too much ice

First - I am not a handyman so bear with me. Turned out not only the auger fins were broken off but also the ice dispenser crusher cover had cracks and breaks on it. First - AppliancePartsPros.com has awesome shipping. Because i didn't know right away the crusher cover was broken, I had to do two orders. Each order was received next day in afternoon. Video is great. Tells exactly how to do. There are two issues you will run into. Remembering the exact sequence of all the washers and... Read more

Replacing head burner d solved the problem. The 8 year old original developed a mild warp, replacing it was the solution. GE gas cook top Model JGP933SEK1SS. I replaced the other burner caps for a cosmetic renewal. Read more

Ordered a new one. took out 4 screws. Pulled the 2 electrical connectors loose and removed. Replaced the same way. FIRST thing to do is to turn off the power. Read more