Need Help?
Call or text
Rear drum bearing kit supports and smoothly rotates your dryer drum. Replace when you hear squealing, screeching, or grinding noises. Verify fit with your model.
Repair went well, replaced the pulley wheel, belt, rear drum bearing. Had an issue after replacement with the dryer stopping after ~5mins or so when running with heat. Fluff cycle would run fine. Details: The lock nut on the pulley wheel didn't feel tight enough so i tried to crimp it back on the pulley arm. It then became way too lose. I had to replace it with a plastic washer I had in my toolkit. That fit snug and seems to work fine. I also added some grease to the pulley shaft under... Read more
Seals dishwasher door perimeter to prevent water leaks during operation. Replace if you notice leaking from door sides or bottom. Easy 5-minute install.
I ordered door seal and bottom strip seal: GASKET TUB PLASTIC Number: WD08X22094 GASKET BEACH PLASTIC: WD08X21894 I had done this once previously and removed the door. That was not too bad but trying to put the door back on the hinges by myself was a bit of work. This time I: 1) removed the 2 screws at the bottom of the door. 2) opened the door all the way 3) slowly pulled the door back on the hinges till I could pull out the bottom gasket 4) slid the new gasket back in place 5) pushed the... Read more
Oven won't heat or takes too long to preheat? A faulty igniter is the most common cause. This round-style gas range igniter is a 15-30 minute DIY fix.
There are two igniters in oven, one for top broiler and one for bake oven at bottom. Your website help me troubleshoot the problem and locate the part. ordered part was delivered the next day. Following the instructions that others on your website had provided, the repair was quick and SUCCESSFUL. No need to pull out oven as power cord can be accessed from removing bottom storage drawer. Step 1: Remove the storage drawer from below the oven and disconnect the power cord from inside. No need... Read more
Oven not heating or takes too long to cook? The bake element provides heat from below. Easy DIY repair with a screwdriver in about 15 minutes.
I cannot not sing the praises of this company & their helpful & fast service. I am going to post the online site address w/my praises on my facebook page for my friends that live on ranches many miles from appliance repair shops & towns. The Oven in our house is for sure over 20 yrs old it was in this home when we bought it, the home is 33 yrs old & the Oven is a Wall Oven, there is not room for a standard Oven in this Kitchen. The Oven itself still looks very nice. About 8 yrs ago or more... Read more
Seals the gap between the drum and front panel to prevent air leaks and noise. Replace if worn, damaged, or causing squeaking sounds. Verify fit with your model.
Found the entire top bearing support plastic piece was completely worn through, the bearing slides had all disappeared some time ago. So it was obviously the problem. The felt trap duct (which is actually a drum seal along bottom front of drum so I don't know why they call it felt trap duct) had also disappeared, so a lot of lint was getting inside the front panel too. It's a very easy repair to change the bearing support; everything just pops out just like the video shows. Make sure you... Read more
Water dispenser won't shut off or no water flowing? This inlet valve controls water to your ice maker and dispenser. DIY repair in 10-15 minutes.
I seared the web and found Appliance Parts Pros site and when I input my GE refrigerator model number I was able to do some diagnostics on their site. It was indicated from my research that the Water Inlet valve most likely was at fault for my problems. I ordered the replacement valve from them and they shipped the same day as the order and it arrived the next day, faster than I had expected. I viewed their video and it was very good at explaining what I had to do to replace the valve on my... Read more
Dryer bearing slides enable smooth drum rotation. Replace when hearing squeaking or rumbling sounds during cycles. Confirm fit with your model number.
A thumping sound (like sneakers in the dryer) started happening. We stopped using it so that it wouldn't get worse and potentially break more parts. Online research suggested rear drive shaft would be the problem. But also suggested while we have the dryer apart, would be smart to replace the belt and the slides/glides (green and white plastic tabs in front, attached to the door). We ordered all the parts from AppliancePartsPros.com and they arrived FAST. It helps to have two people for this... Read more
Freezer coils icing up and fridge too warm? This defrost thermostat monitors evaporator temperature to prevent overheating. Easy 20-minute DIY fix.
I unplugged the fridge and took all the food and shelving out of the freezer and then proceeded to take off the bottom sliding drawer rack on both sides off (4 Phillips head screws). Then took off the light bulb cover and then the light bulb. Then the back wall that covers the coils and tubes that the refrigerant runs through ( 2 screws with hex head). After sliding out the back wall I could see that the entire coil area was frosted and iced up. I took a blow dryer and melted all of it over... Read more
Burner stuck on high or won't heat? This 8-inch infinite switch controls heat output on electric ranges. Simple 20-30 minute DIY replacement.
I replace the Infinite Switch and that seems to be the trick for keeping the temperture under control. Read more
Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.
By visiting your website, viewing the repair instructions and ordering the right parts. Very easy to understand and to do the repair.. Read more
Dryer won't start when you press the button, or stops when released? The push-to-start switch often fails. Easy 20-minute DIY repair with video.
I was trying to troubleshot a problem I had with my GE dryer not starting. I went to AppliancePartsPros.com because they have excellent DYI videos on how to make repairs. I determined that the problem was in the push start switch. I ordered the switch online and it took 3 days to arrive. It took 5 minutes to replace the switch and the dryer works perfectly. Read more
Fix F2 error codes, dead oven display, or overheating issues. This oven control board manages temperature and cooking modes. DIY-friendly repair.
Replaced control board myself. Easy. Read more
Washer won't drain or leaving standing water? This drain pump removes water at cycle end. DIY-friendly repair, typically 30 minutes with basic tools.
I opened the cover panel of the control board. I visually checked for burns on the board and verified all connectors were firmly seated. I opened the bottom of the unit, and I saw the service manual in a zip-lock bag. From this manual, I verified that the drain pump resistance is good, the start capacitor is good, and the lid switch is good. I entered diagnostic service mode. Persistent alarms are 4 and 25.Error 4 means Reset Monitor, while Error 25 means Pressure Sensor Dropout. I... Read more
Replace your cracked, rusted, or stained 8-inch range drip pan. Installs under the large burner to catch spills and protect your cooktop surface.
I spent hours searching for the right trays, knowing only that the stove is GE, and what the trays look like, including exact dimensions. I ordered one set that had exact measurements, and they even explained how the measurements are taken. But the trays were larger than described by 3/8 inch, and I had to pay shipping to return them. I suggested that they correct their description, but the lady did not think I was right. I said just measure them yourself, as per the method that your... Read more
The Dryer Bearing Slide (2-Pack) is an OEM replacement part for GE dryers. These slides are installed on the front panel of the dryer and support the drum as it rotates. They help reduce friction and wear, ensuring smooth and quiet operation during drying cycles. This pack includes two bearing slides, which are commonly used together in the dryer assembly.
Over time, bearing slides can wear down due to regular use, heat, and friction. When they become worn or damaged, the drum may no longer rotate smoothly, which can affect the dryer's performance and increase noise levels.
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
White plastic timer knob for dryer control panel. Replaces cracked, broken, or stripped knobs that prevent you from selecting drying cycles.
The thermostat knob on my dryer broke and I couldn't find it in any of the stores in my area. I looked online and it was very expensive. I found your website when I went to Lowes. The gave me a card with your site. The knob was very reasonable, came within a week and I was able to put it on in a second! It was a very rewarding experience. Read more