Jenn-Air Parts

• Leaking

After discovering your web site and reading of others issues I ordered a door seal (my old one was a little short on the right side) a detergent door grommet, and the 2 water deflectors ( I decided to cover all the bases while I was at it. Very simple job with the information provided on your web site. I certainly have the confidence to tackle other appliance repair now. Read more

Ordered a replacement part off another site that came in with an incorrect molded connection to the Spray Arm. The part broke my tabs on the Spray Arm and instead I bought both parts from this site. Both items were correct and resolved the issue. Read more

Started my Maytag dryer (model LDE8200ACW) with a large load early Saturday morning and immediately heard a noticeable thumping noise as the drum turned. Opened the door and checked to make sure some of the laundry hadn’t wadded up and was causing the thumping. Restarted it but the thumping was still present. Did a google search for obvious possible causes for the symptoms but the only suggestion that made sense was to check and make sure the dryer wasn’t rocking on its feet. Checked and found... Read more

So this is a poor design in the first case. Not having a center support in the back almost guarantees a failure there eventually. I kludged together a support in my original more than a year ago, but finally the part broke too bad to limp along with anymore. This is the part I needed. That being said, be very attentive about the fact that it's not the entire shelf assembly. There is a metal support across the front of the frame that is not included. The trim above the drawers, and the... Read more

We turned off the circuit breaker. We then removed the light cover and then the control panel. We disconnected the Keyboard, Utah, plugged in the new one and turned the breaker on to see if everything worked. We realized that we did not need a new jazz board so that is being returned. The old Keyboard was removed, the new one attached and all the parts were put back. The frig works fine now at the recommended settings of zero and 38F. Read more

• Little to no heat when baking
• Oven not heating evenly
• Oven is too hot
• Won't start

I'm a 66 year old woman (on a fixed income) and I'd never before repaired an oven bake element . My stove is 20 years old but I still found it was much more affordable to change the bake element rather than buying a new stove. I called the number on the website and talked to a very informative woman. She answered all the questions I had about my stove. She told me about the repair video on the website which had step-by-step instructions. I ordered a new element - received it within 4 days.... Read more

1. Ordered new gasket. 2. Heated with blow dryer gasket until it resumed its normal shape. 3. Turned off refrig. 4. Cleaned freezer compartment. 5. Removed old gasket. 6. Installed new gasket. 7. Turned on refrig. 8, Operation back to normal in about 6 hours. Read more

Ordered new drip pans from Appliance Parts Pros, hoping they'd fit perfectly...and THEY DID! We are so happy with them. The ones at other places didn't. Read more

Given all the symptoms, we figured that the control board went out. First, unplug the refrigerator. The control board was easy to access by removing a panel on the back of the fridge. I unplugged all the connectors and used a putty knife to release the board from the plastic retaining clips. There was some browning on the underside of the board and the back of the refrigerator that suggests one of the capacitors on the board blew. Install the new board by pressing it into the retaining clips... Read more

After checking other reviews, we decided it was best to replace the interlocks, cam and all three switches. You're going to need a phillips screwdriver, star driver, small screwdriver and needle nose pliers. You need to remove the ONE Phillips screw above the control panel inside the vent. The contol panel is on hinges that you can slide up and towards you. Using caution remove the wires noting how they're connected. Pinch the top of the white connectors and wiggle them free. We couldn't get... Read more

• Light not working

We had delayed repairing the problem because we received a price of more than $ 100 from a local appliance repairman. However, after viewing the view on the ApplianceParts Pro website, I saw what an easy repair it would be. After receiving the part from you, I had my son do the repair because I felt it would a good father - son bonding time. It was so easy and he was proud of his ability. Thanks for your excellent repair video and the excellent price. It costs less than $ 22 instead of more... Read more

• No hot or cold water
• Will not fill with water
• Will not stop filling with water
• Noisy

1. Sleeve for input, Injector valve, nozzle and seal for input fixed this problem. Probably the main part that was the trouble was a deformed Injector Valve which is a rubber tube with an internal retention groove at the wide part that grips the Nozzle. The Sleeve and the Nozzle are hard plastic parts that basically looked fine, but I replaced them anyway while I was in there. Additionally I replaced the rubber Seal for Input which seals the plastic input fitting to the tub just to make sure... Read more

If the freezer is cold and the fridge is hot, logic would indicate that the fan blowing the cold air from the freezer into the refrigerator is not working. Searched the ApplicancePartsPros.com website for a fan in the freezer compartment and found the video on how to replace one. Followed the steps in the video to get the freezer partially disassembled and found the whole back of the freezer frozen over. Plugged the refrigerator back in and verified that the fan was not working. Unplugged... Read more

New door seal did the trick. Read more

Replaced lower and upper element. Internet research suggested it was the control board. Thankfully it was a much quicker and cheaper fix. Read more

• No heat or not enough heat
• Takes too long to dry

I had to pop the lid up from the front with a screw driver, and behind the element was a metal piece, a heat shield, that had two screws that had to be removed from the back. The little part with the blue round tag (part of the kit that came with the element) was easily removed with one screw. Likewise, the element had a single longer screw holding it in on the right, and on the left a little rod was sticking through a hole in the metal, and you can merely move it to the side and up the slot,... Read more