Need Help?
Call
Fix washer display issues, cycle problems, or unresponsive buttons with this electronic control board. Direct replacement restores full functionality.
Fix a dishwasher that won't start, stops mid-cycle, or has a blinking light panel. This control board regulates all wash cycles and functions.
Replaced control board. This did the trick! The dishwasher works great again. Read more
Usually ships within 4 - 14 days
Fix a dishwasher that won't start, has flashing lights, or locked control panel. This electronic control board manages cycles and operations.
Removed and replaced part arrived sooner than expected thank you so much!!! Read more
The Electronic Control Board is an OEM part for Whirlpool dishwashers. As the central processing unit, this board regulates all wash and rinse cycles according to preprogrammed instructions. It communicates timing and commands to other crucial components.
Symptoms of a faulty control board include:
Causes can involve water intrusion corroding circuits or individual component failure due to prolonged operation. Over time, environmental factors may inhibit board performance.
This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
It's very easy fix. If your unit flashing e2 f2. It's your relay board take screw if on door couple latched s on the gray relay box pull wires harness of slow. Re install the same way it came of Just remember to cut the power off first . Leave your door open when re powering unit. Read more
Dishwasher won't start, lights blinking, or cycles not completing? The electronic control board manages all wash functions. Moderate DIY repair.
Ordered the electronic board for the dishwasher and replaced it. And it fixed it. Read more
Refrigerator won't respond or shows error codes? This power control board regulates operations and coordinates key components. DIY-friendly repair in 10 minutes.
DIY the part worked fine Read more
Dishwasher won't start or lights flashing? The electronic control board manages cycles and timing. Moderate DIY repair restores full operation.
Replaced control board Read more
Washer stuck between cycles or skipping rinse? This timer controls cycle sequence and duration. DIY repair typically takes 10-15 minutes with basic tools.
I knew the timer was bad. I went to the parts train website as i had done before. I found the part in just a few moments. It arrived in 2 days and I replaced the timer. 4 screws and 10 minutes was all that it took. Read more
Refrigerator not defrosting or icing up excessively? A failed defrost timer won't cycle between cooling and defrost modes. Moderately easy repair restores function.
Tested for faulty defrost timer, replaced it Read more
Fix a dead oven, erratic display, or locked controls with this range oven control board. Controls temperature settings and timers. Takes about 10 minutes to install.
Unplugged wires, took it out, inserted new panel, it plugged wires. Read more
Range not responding to buttons or display blank? This electronic control board manages oven functions, timers, and cycle sequencing. Moderate DIY repair.
Fix a washer that won't advance through cycles or stays stuck on one setting. This mechanical timer restores proper cycle sequencing. 1-hour DIY repair.
Replaced the washer timer. I have been able to coax a bit more life out of these timers by using electrical cleaner and/or emery paper. Cleaning is only borrowing time though. I have replaced this same part three times now, but over a (roughly) 12 year period of time and nearly daily use. Not very difficult. I would rather keep fixing this older unit than pay a service tech big dollars to repair a newer unit. (Typical experiences of friends and family members.) I also clean and store the old... Read more
Fix a washer that won't advance cycles or start filling water with a new timer. Controls cycle timing and electrical components. 10-15 minute DIY repair.
Very easy - removed cover, removed dials (had to look at new one to see there were threads on the shaft so the dial had to be screwed out. Two screws holding timer to faceplate. Two connection plugs that came out easily. Job took 10 minutes. Read more
This electromechanical timer assembly controls cycle timing for compatible GE ranges and ovens, restoring accurate cook cycles and timer functions. It replaces a worn or non-advancing control to help your appliance complete timed operations reliably. What it does:
I looked up my dryer on this website, then ordered that one. Later put it in myself. There was a nice note in the box telling to move one terminal from the old timer to the new one if it is missing the white wire, and transfer the resistor over to that, which I did and all went well. Dryer automaticly counts-down and turns off by itself now... Read more
This replacement board-switch is the electronic control that manages user inputs and basic appliance functions, restoring reliable response from the control panel. Use it to replace a faulty board causing unresponsive or erratic controls. What it does:
Fix a blank or unlit oven display with this range digital control board. Controls clock, timers, and timed baking cycles. Easy DIY repair in under an hour.
After I received the new control board from AppliancePartPros.com. My husband just unscrew the old one and replaced the new one, that is really easy fix. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.