Kenmore Elite Parts

Motor had to be replaced. Wiring at motor was burnt. Also replaced belt and belt switch while it was apart. Read more

Watched the video here, took the leap that burner was the problem and ordered it. Also found another vid on you tube that was more specific to my Kenmore. Tip: find out how to take off the oven door. For mine it was very easy but not detailed in the APP vid. I followed instructions in APP vid but also first took off back panel of range and tested resistance of old burner to ensure that was truly the problem (as suggested by other YT vid). Also, dis/connecting the wires from the back is easier... Read more

Replaced sump, wash pump, drain pump, diverter motor, and thermostat. Read more

• Little to no heat when broiling

I replaced the element. I went on your site to order a new element, and had trouble locating the exact replacement. A young man named Kenneth came on live chat and assisted me. He found the correct one and assisted me with the order. It was all very smooth and quick. I received the part in two days ! Read more

I unplugged the stove ,cut the 50 amp cord off from the terminal block as it was burned took out the terminal block as it to was all melted .installed the new terminal block with a new stove cord back in business Read more

Searched the web and determined it was something called a noise filter. Ordered the part from ApplianceParts Pros. Received it in about 3 days, normal shipping. Replaced the part. Took about 15 minutes from start to finish. Problem solved. Cost less than $50. Read more

The repair was a success. The switch and came looked different from the original. I called Appliance Parts Pro, they lady on the phone said that Frigidaire changed the switch and how to wire it up correctly. Problem solved. It all works as it should. Read more

I ordered a new socket and replaced the socket and now we have a light in the oven. The project took about 10 minutes and was easy done. Read more

• won't spin
• Will not agitate

I looked on the internet for similar descriptions for similar models and found many angry reports. Most said that the rotor assembly was bad as the nut that held the rotor and other parts together had loosened and allowed slippage between steel and plastic splines. Yes, I know that sounds like trouble, but apparently not to LG when they designed it. Most buyers complained that the part was covered by warrantee but not the labor and labor had been quoted as $400 to $600 dollars. Time to buy... Read more

1. I unplugged the washer from outlet 2. I turned off the hot and cold water taps going to the washer (both just in case) 3. Draped a towel over back edge of washer and under where hoses coming from water outlets attach to back of washer (to catch any loose water out of the hose or screw nozzle leading to valve assembly, then unscrew (by hand) the cold water hose from back of washer (leave hot water hose alone as not needed). 4. Unscrew valve assembly from washer by two screws on back top of... Read more

• Leaking

I replaced to offending part. The only minor issue was that the replacement part had changed design from the original. Otherwise it was a pretty straight forward operation. Read more

Ordered 6 parts from you thanks to your fantastic web schematic parts diagram received parts very fast changed parts easily and that leak stopped. Your company is a 5* operation hands down. Read more

Once I was convinced that the water supply and filter wasn't the problem, I took the back protective panel and looked at the valve assembly. It looked corroded, especially on top where the ?pistons for the solenoids?would project into. I ordered the part and it was on my doorstep in TWO days...really fast. The part was slightly different from the one that I was replacing in that the part was "angled out." This was not a problem. All that did was tilt the fitting for the copper water line... Read more

Ordered new wheel assembly, which came in about a day and a half. The broken assembly was on the left front so I only had to slide the dishwasher out just enough to expose the two mounting screws on the outside of machine.When you remove the old assm there are two rubber washers on the back side. If you didn't order new ones,remember to remove them from broken assembly and install them onto the new piece.Overall this is an easy fix and took about ten minutes including pulling the machine away... Read more

Ordered replacement parts Read more