Need Help?
Call
Refrigerator stopped cooling after power outage? The compressor overload protector prevents overheating damage. Easy DIY fix when compressor won't run.
Removed and replaced the compressor start relay. Read more
Seals refrigerator door to prevent warm air entry and maintain temperature. Replace if torn, cracked, or moldy. Confirm fit with your model number.
The right door seal and the freezer door seal are easily removed and replaced. They just pull out of the slot. These 2 new gaskets push in easily. The left door has the French Door Mullion, that blocks the removal of the door gasket. There are two screws in the middle that holds it on, and there is a spring at the bottom of the mullion that keeps the mullion in place. The spring can easily be removed, or left in place. There is an electrical connector in the middle of the mullion. As suggested... Read more
Refrigerator clicking but not cooling? The compressor start relay kickstarts your compressor. Simple 30-minute DIY fix that gets your fridge cold again.
Replaced the Thermistor Assembly and also picked up Overload Protection circuit per the comments posted by the "experts" on the web site. Both parts cheap enough. I ordered parts at 3:30 in the afternoon and they showed up the next morning from half way across the country. Outstanding service. It also fixed the 9 year old refrigerator. Replacing the parts took about a half hour most of which was moving the unit from the wall and removing the panel to get at the parts. Read more
The Ice Dispenser Door Motor is an OEM part for LG refrigerators. This motor is responsible for the operation of the ice dispenser door, controlling its opening and closing mechanism to allow ice to be dispensed without letting warm air into the freezer.
Symptoms of a bad Ice Dispenser Door Motor include:
Causes of ice dispenser door motor failure can include electrical issues such as shorts or wiring problems, mechanical wear over time, or blockages that strain the motor.
This OEM LG part is also compatible with Sears/Kenmore.
Unplug refrigerator. Use non marring (plastic trim stick) tool to gently pry loose the plastic assembly containing the PCB display beginning at the lower edge and proceeding around the outer edge. Disconnect all connectors and note the routing of each wire harness and connector (take pictures on cellphone as necessary). Remove two screws holding inner PCB mount bracket in place to expose actuator, flapper door and linkage. Replace actuator (three mounting screws) and ensure that actuator... Read more
Replacement left adjuster housing for dishwasher upper rack. Restores proper rack alignment and stability. Needed when housing is cracked or broken.
We looked for a supplier of the part and came across AppliancePartsPros. They had the parts in stock and the prices were reasonable. We ordered the parts sometime on Thursday afternoon. The needed parts arrived on Friday around 11:00A. Wow, what fast service! Read more
The Diverter Motor Assembly is an OEM part for LG dishwashers. It is a critical component used to control the direction of water flow within the dishwasher, ensuring that water is properly diverted between the different spray arms during various wash cycles.
Symptoms of a failing Diverter Motor Assembly include:
Causes of a bad diverter motor can include wear and tear from regular use, electrical issues such as faulty wiring or motor failure, and mechanical obstructions or debris that prevent the diverter from moving smoothly.
This OEM LG part is also compatible with Sears/Kenmore models.
I ordered a new vario motor and a soap dispenser. I turned off the water and the breaker, disconnected the water line and the power at the front base of the unit, disconnected the drain hose from the garbage dispenser, and pulled out the dishwasher and laid it on a blanket on its face. I unscrewed and removed the plainly visible vario motor on the bottom of the machine and removed the cam from the shaft. I then used a needle nose plier to carefully turn the D-shaft on the new motor to exactly... Read more
This tube supplies water to the ice maker and water dispenser systems, running from the water source to the dispensing mechanisms. Replace when you experience low water flow, no ice production, or visible leaks along the water line path.
Ordered new tube part AJR56656503 for Lg LFX25978ST/01 watched a lot of videos but none showed how to remove the door tube end from its connection so I just cut and spliced the new tube to the old under the cover for the door hinge area after feeding it from the back of frig to that area. It was easy till I tried to remove the line end from ice maker area. Read more
Seals refrigerator door to maintain temperature and energy efficiency. Replace if torn, cracked, or not sealing properly. Verify fit with model number.
Insulating seal for bottom-mount refrigerator freezer doors. Replace if frost buildup, ice forming, or warm air entering. Confirm fit with your model number.
Replaced freezer door gasket. Door gaskets needed replacement did those as well Read more
Seals the float switch base to prevent leaks during dishwasher operation. Replace if water leaks from below the float assembly. Confirm fit with model.
Ordered 6 parts from you thanks to your fantastic web schematic parts diagram received parts very fast changed parts easily and that leak stopped. Your company is a 5* operation hands down. Read more
Adjuster cover for dishwasher upper rack height adjustment mechanism. Replace if cracked, broken, or missing to protect adjuster components from water.
While this is a Whirlpool dishwasher, I have the Kenmore Elite version of it. I believe them to be identical for parts. A little background: The first symptom I had of problems was plastic bits from the ball bearing retainer strips in the slides falling out. Then ball bearings falling out. A common problem with this dishwasher. When disassembling the upper basket, some of the gray plastic pieces were very brittle and easily snapped off. So I ended up replacing all of the plastic pieces related... Read more
Plastic door stop that limits refrigerator door swing range. Replaces broken, cracked, or missing stoppers causing doors to swing too wide or close improperly.
1. Googled "appliance replacement parts" - found two sites to consider 2. Researched parts needed via a exploded diagram - can't fix it if you can't name it. 3. AppliancePartsPros.com had the easiest diagram and after checking, the lowest price. 4. Parts showed up within a couple of days - an in-transit note was helpful. 5. The part screws in but watch out you don't break the tiny black pin holding the part on in addition to the screw. Needed JB Weld to fix that. Read more
Fix a washer that won't drain or leaves standing water with a new drain pump assembly. Common DIY repair that restores proper water removal each cycle.
Had to replace the drain pump and the PSB main board. Read more
Replacement door hinge bushing for refrigerators. Installs in door hinge mechanism. Replace when worn, cracked, or causing door grinding or misalignment.
Elderly neighbor charged $100 for factory tech to inform her that the part wasn't available anymore, so I ordered 2 from Appliance Parts Pros.com (one for a spare) and when they arrived a few days later, I installed then in about 20-25 minutes. I had to remove all the food off the door shelf so I could lift the door off the hinge to replace the bushing. That took 5 minutes. Shame on the tech that went by the date of manufacture rather than checks by model and serial number to see if the part... Read more
Replaces the flap panel between French doors that seals the center gap. Order when original is cracked, broken, or won't stay closed properly.
I replaced the part Read more
The Tray Asm is an OEM part for LG refrigerators. It is designed to store fruits and vegetables at optimal humidity levels, helping to keep produce fresh for longer periods. It has approximate measurements of 30 inches in length, 18 inches in width, and 4 inches in height.
Causes of a bad tray asm can include cracking or breaking due to frequent use, accidental dropping, or exposure to heavy loads that exceed its capacity. Over time, the plastic can also become brittle and more susceptible to damage.
Symptoms of a bad tray asm include:
All three were replaced inside of 10 minutes. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.