Kenmore / Sears Parts

• Fridge too warm
• Freezer section too warm
• Noisy

Replaced compressor fan. the video on the website showed step by step. very easy and it fixed the problem. Read more

I bought the listed condenser fan motor for my Maytag refrigerator. Access to the condenser fan is by removing sheet metal screws of bottom panel with 1/4 in. nut driver. Condenser fan is on left side of rear access area. Remove electrical connector by pressing-in connector release tab with thumb fingernail and pulling on connector. Remove three mounting screws with 5/16 nut driver. Work fan out to the right past the compressor. I used a pair of pliers, as a lever, behind the plastic fan blades... Read more

I first thought it was the auger in the ice container so I changed it and it was not the problem. I then talked to ApplianceParts customer service that it might be the yoke on the motor that turned the auger or even the motor itself even though it worked. I ordered the parts, the yoke was supposed to be able to be changed by itself but mind would not come off the motor shaft so I had to cut it off just to remove it from the unit so I had to change the motor anyway because of this. So I advise... Read more

My KitchenAid refrigerator was not cooling, but the freezer was working perfectly. The help section here listed three parts that could be defective–defrost thermostat, evaporator fan motor and blade, and air diffuser/damper control–so I replaced them all. The videos were EXCELLENT, and despite the difficulty I had squeezing my shoulders into the small freezer compartment, I installed the parts and my refrigerator is cooling perfectly! THANK YOU FOR THE EXCELLENT REPAIR VIDEOS! I am so happy... Read more

In short - I replaced the evaporator fan motor and the evaporator fan blade. The Appliance Parts Pros website was extremely helpful to me. Here's how. 1. The site helped me identify that even though my Freezer says it's a Frigidaire, it's actually an Electrolux. 2. The site identified the potential screech causing parts. (I didn't take a chance, I bought all three) It was a worthwhile investment. My freezer is 20 years old so it deserved some help. 3. The site provided guidance videos (not... Read more

• Noisy
• Tray won't turn

I fix this problem by purchasing a new turntable motor. Simple 5 minute installation. Read more

• Will not agitate

Swapped bad part for new part. Read more

First, I did online research to find out what could be the problem with these symptoms of cold freezer and warm fridge. I found multiple posts with people going back and forth as far as what to do to fix it. One tread even provided the link to your store with the part number for the evaporator fan motor. So I did the inspection of the motor as suggested by the expert and sure enough it was the evaporator's motor fan that was not working as it should. That is when I immediately follow the link... Read more

Ordered the two motors plus ordered the fan blades since I was afraid one might break during replacement. Changed out without breaking Freezer and both ice makers now working fine Read more

The repair went well. Never made this type of repair before. Took me around 90 minutes to complete. The worst part was winging it on how to disassemble the bottom drawers. On my Kenmore Elite, it has three freezer compartment sliding trays. The other difficult part for me was removing the clipped in part on the back of the freezer panel. Without knowing what to do it was a little frustrating. after getting to the evaporator unit, removing built-up ice and replacing the unit was fairly easy. The... Read more

I received my new part in about 3-4 days. Part was exact match for my existing motor. After watching the installation video on this website I was able to garner the rudimentary directions to replace the motor. The video did not match the exact fridge I had. My fridge did not have the access panel on the interior of the freezer. I had to remove the two screws at the water ice dispenser tray on the outside and slide that unit off the front. Before removing the motor, open the freezer and remove... Read more

Removed the rear cover from inside the freezer section, found the evap fan not working. Ordered replacement motor, easy change. Read more

My problem started with a rusting condition in the ice bin that spiraled out of hand. I took apart the ice bin and all the hardware thinking I could clean it with the suggested baking powder. Plastic parts cleaned up like new, metal parts were pitted. I wire brushed and sanded the parts put it all back together and gave it a try. All appeared fine then two days later the ice dispenser stopped. I watched a couple of videos and most pointed to the ice auger motor. One video specifically said you... Read more

• won't spin
• Will not agitate

I looked on the internet for similar descriptions for similar models and found many angry reports. Most said that the rotor assembly was bad as the nut that held the rotor and other parts together had loosened and allowed slippage between steel and plastic splines. Yes, I know that sounds like trouble, but apparently not to LG when they designed it. Most buyers complained that the part was covered by warrantee but not the labor and labor had been quoted as $400 to $600 dollars. Time to buy... Read more

• Noisy
• Freezer section too warm
• Fridge too warm

Once I purchased the correct motor it literally took less that 10 minutes from start to finish to replace the motor. After unplugging the refrigerator, I unscrewed two machine screws to remove the cover and unscrewed two machine screws to remove the motor. I removed the old motor from the housing, installed the new motor, reattached the motor to the refrigerator, replaced the cover, and plugged in the refrigerator. Installation was quick and simple. AppliancePartsPros service was excellent... Read more

After checking the suggested fixes and parts on Appliance Parts Pros, I ordered the defrost thermostat and evap motor for my refrigerator, a Kitchen Aid KSSC42QTS00. Installation was very easy, simply emptying the freezer and removing the access panel in the back bottom half. Upon getting everything open, I found out that the existing evap motor was working fine, so I didn't install that part. I did install the defrost thermometer, which was a 5-minute process. I also cleared out the vent... Read more