Kenmore / Sears Washer Agitator Parts

This was a fairly easy fix. The only problem I had was that the cover over the retaining nut was difficult to pull off. I changed to a larger pair of pliers and put a little more muscle to it and it popped right out. There was a little corrosion on the shaft that needed to scraped off for the new agitator to slide on easily but after that was gone the new part slid on and with some downward pressure it seated in. Read more

Replaced agitator and washplate bolt and washer. Normally this would have been a 5 min job, however the bolt wouldn't come loose. The teeth on the agitator were worn down and the shaft the bolt screws into would turn with the bolt when trying to loosen it. I had to cut out the agitator using a dremel and hold the shaft in place with a vise grip in order to unscrew the bolt. Once the bolt was out I used WD-40 to help get the agitator off the gears. Job took much longer than normal, but I... Read more

Ordered a replacement part and a new screw. About a dozen YouTube videos later managed to get the old one-off. Best to use a power tool! Once we figured that out we were done replacing the part in less than 5 minutes. Read more

Simply lift up the old filter and cap and discard it. The new assembly simply pushes down and on to the agitator base. It stays in place by clicking over a raised perimeter rib on the base. This is the easiest repair (short of screwing in a light bulb) that one could do. The hardest part was to identify which parts I needed to purchase. The parts associate at Appliance Pros was terrific in tracking down what was needed. Read more

Very easy fix! Order shipped fast and received the item in a couple of days with a 10 minute fix! The step by step video helped most! Thank you so much for this website as it probably would of cost me at least $125 to fix! Read more

I watched the Youtube video from AppliancePartsPros.com, bought the agitator kit, rewatched the video, installed the parts, washing machine working like new. Phenomenal. Read more

At first, I thought, maybe I should just get a new washing machine. After all, it is almost 20 years old! I couldn't bring myself to do that and said to myself, let me see if I can figure out what parts I need and see if I can find a video that tells me how to do it and see how hard it is. I’ve never attempted appliance repair before. After figuring out what the most likely parts were, I ordered the water level switch and agitator cam repair kit - I figured for $10 more, I might as well... Read more

I had replaced the Agitator cams a couple of times already due to my brother-in-law overloading the machine which stripped the teeth off of the cams. I also noticed the agitator seemed to 'wobble' and made 'knocking' noises quite a bit. I reviewed the video on the Appliance Parts Pros web site, disassembled the agitator and cleaned everything up, which helped a little, but not enough. Figuring the agitator itself was worn out also, I looked up and ordered all the parts for the upper agitator on... Read more

A buddy of mine gave me a washer and said if you can fix it you can have it, It doesn't spin. I tried running a spin cycle and found that it did try to spin but was very noisy. I disassembled the washing machine and found that the tub seal had gone out and took out the bearings with it so I ordered a new tub and seal kit and while I waited for that I proceeded to disassemble the rest of the washing machine and clean everything so when the new parts arrived it was ready and waiting. Bearing... Read more

My wife noticed that our washing machine was making a terrible rumbling noise and seemed to be out of balance all of the time. She was on the verge of calling a repairman when I said I wanted to look at it first. I noticed the agitator was very loose and would spin in your hand. I removed 1 bolt and the agitator was out. The teeth in the agitator were stripped out so by simply ordering a new agitator and installing it I turned a $250.00 repair call into a $70.00 DIY fix. Thanks. Read more

Replaced top part of agitator and agitator dogs. Repair video very helpful. Read more

Simple by using 7/16 socket with long extension to remove the bolt and pull the whole agitator out and clean them. Put back in together with new parts. It works fine now. Read more

I ordered all parts of the agitator top, matchup was exactly the same and replaced them quickly. Read more

Ordered a agitator Read more