Kitchenaid Hinge Parts

Fresh freezer cabinet top hinge.

This gap hinge is a direct-fit door hinge that helps maintain correct alignment and spacing between refrigerator doors for smooth opening and a consistent seal. It restores proper door positioning and reduces rubbing or uneven gaps. What it does:

• Supports and pivots the door to maintain correct alignment and spacing
• Prevents door binding, uneven gaps, and rubbing against adjacent surfaces
• Helps doors close fully to preserve the fresh seal and temperature control
• Durable metal construction designed for repeated door cycles

• Use appropriate hand tools and keep power to the appliance off when adjusting nearby electrical components or lighting
• Follow manufacturer torque and alignment recommendations to avoid misalignment or seal issues
• Inspect surrounding hinges and mounting hardware for wear and replace as needed

This stop-door is a small replacement door stop that helps control how the appliance door closes and rests, restoring proper door movement and preventing over-travel or binding. What it does:

• Cushions and limits the door's travel to prevent slamming or over-rotation.
• Helps the door align and latch correctly when closing.
• Can reduce door sag or rubbing caused by a worn/missing stop.
• Addresses symptoms such as a door that closes too far, hangs unevenly, or doesn't sit flush.

• High-level, two-person recommended for larger doors; support the door before removing fasteners.
• Disconnect power (and water if applicable) and follow manufacturer safety guidance before servicing.
• Use appropriate hand tools; inspect adjacent hinges and fasteners and replace if damaged.

This door hinge secures and pivots a refrigerator door, restoring smooth opening and proper alignment to prevent gaps and uneven closing. Designed to match OEM form and fit for reliable operation. What it does:

• Provides a durable pivot point so the door opens and closes smoothly
• Restores proper door alignment to improve sealing and cooling performance
• Reduces door sag and uneven gaps that can cause leaks or rubbing
• Fits the original hinge location and mounting pattern for correct operation

• Support the door before removing the old hinge to prevent injury or damage
• Disconnect power to the appliance if required for access or to avoid electrical components
• Use basic hand tools; follow OEM instructions for torque and fastener sequence
• Inspect and repair before installation if hinge mounting holes or door alignment are damaged.

A non-metal shim used to stabilize and level your appliance for quieter, more reliable operation. Simple, low-profile support that helps correct minor height and balance issues so doors and drawers align and appliances sit securely. What it does:

• Adds thin, non-metallic spacing under feet or frame to correct slight height differences
• Helps stop rocking or tipping that can cause noise, vibration, or misaligned doors
• Supports even weight distribution to reduce uneven wear on adjustable legs
• Useful when adjusting leveling feet can't fully correct a gap or tilt

• Place shim under the appliance foot or frame where additional height or support is needed
• Re-check appliance level and stability after installing; add/remove shims as required
• Use with care to avoid creating instability; pair with proper leveling adjustments

This center hinge pin kit secures the middle hinge on compatible refrigerators so the door stays aligned and operates smoothly. It restores proper door pivoting and reduces sagging or uneven closing. What it does:

• Replaces worn or bent center hinge pin to restore correct door alignment
• Helps stop door sag, rubbing, or gaps that affect sealing
• Reduces noise and sticking when opening or closing the door
• Works with the center/middle hinge assembly to maintain smooth pivot action

• Follow the refrigerator's service manual for disassembly; some models require removing the door or shelves
• Support the door during removal/installation to prevent damage or personal injury
• Use proper tools and avoid over-tightening hinge fasteners

This door hinge is the factory-style replacement that lets a refrigerator/freezer door pivot smoothly and stay securely aligned. Restores proper door movement and helps prevent sagging or gaps that keep the door from sealing. What it does:

• Provides the pivot point that allows the appliance door to open and close smoothly
• Supports the door weight to maintain proper alignment and sealing
• Helps eliminate door sag or uneven gaps that can cause cooling loss
• Restores normal door operation when a worn or damaged hinge causes sticking or misalignment

• Disconnect power and empty the door before starting; work on level ground
• Use appropriate hand tools; support the door during removal and reinstallation
• Align hinge and door carefully to ensure an even seal; tighten fasteners to manufacturer torque if specified

This top door hinge secures the refrigerator door to the cabinet and lets the door pivot smoothly. Replace a worn hinge to restore proper door alignment and even sealing for better cooling performance. What it does

• Supports the top of the refrigerator door and provides the pivot point for opening and closing.
• Helps keep the door aligned so the gasket seals properly and cold air stays inside.
• Worn or damaged hinge can cause door sag, uneven gaps, rubbing, or noisy operation.
• Restoring the hinge can reduce stress on the door and other hinge components.

• One top door hinge.

• Basic hand tools are usually required; support the door while removing or installing hinges to prevent injury or door damage.
• Disconnect power only if working near electrical components; this hinge replacement typically does not require electrical disconnection.
• If the door was removed, recheck alignment and gasket contact after reinstalling; adjustments may be needed.
• Follow OEM instructions and use proper safety equipment.

This door hinge replaces a worn or damaged refrigerator door hinge to restore proper door alignment and smooth opening. It helps the door sit squarely and close reliably to maintain a good seal. What it does:

• Supports and pivots the refrigerator door so it opens and closes smoothly
• Corrects door sag or misalignment that can cause gaps or uneven sealing
• Reduces rubbing or binding between the door and cabinet
• Helps prevent cold air loss from a door that won't fully close

• One door hinge

• Disconnect power to the appliance and remove food from the door shelves before starting
• Support the door while removing hinge fasteners to avoid dropping the door or injuring yourself
• Use appropriate hand tools; avoid over-tightening fasteners when reinstalling

The Door Hinge (RH) is an OEM replacement part for Whirlpool dishwashers. This hinge is installed on the right-hand side of the dishwasher door, allowing it to open and close smoothly while maintaining the proper tension and alignment. The hinge plays a crucial role in ensuring the door seals securely during operation, preventing leaks and enabling efficient cleaning performance.

Common causes include regular use leading to wear and tear, accidental impacts, or exposure to moisture, which can contribute to rust or corrosion.

Symptoms of a bad door hinge include:

• The dishwasher door not closing completely
• Difficulty opening or closing the door
• A sagging or misaligned door
• Unusual noises when moving the door

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Replacement door hinge designed to restore proper alignment and smooth opening for compatible refrigerator doors. Replaces worn or damaged hinges to reduce sagging, rubbing, and uneven closing for better seal and operation. What it does:

• Supports and pivots the refrigerator door for smooth opening and closing.
• Restores correct door alignment to improve gasket contact and cold-air seal.
• Stops door sag, uneven gaps, or rubbing against the cabinet.
• Helps eliminate noisy or stiff door movement caused by a worn hinge.

• Disconnect power to the appliance and remove food from the door area before starting.
• Support the door securely while removing and installing the hinge to prevent dropping or damage.
• Reuse original fasteners only if undamaged; replace any stripped or corroded hardware.

Top hinge assy-rh gal

Color: White

The Door Hinge is an OEM part for Whirlpool refrigerators. It acts as the pivot point that allows the fresh food door to open and close smoothly. As a moving component subjected to frequent use, the hinge can become loose or misaligned over time.

Causes can be normal wear and tear, excessive force on the door, or improper alignment over repeated use. Installation of this genuine replacement restores reliable door function.

Symptoms of a bad hinge include:

• The door not closing or sealing properly
• Difficulty opening and closing the door
• Noises or squeaking coming from the hinge area

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This oven door hinge restores smooth, controlled door movement and a proper seal. Worn hinges can cause a sagging door, poor closure, or binding—replacing the hinge helps maintain safe operation and consistent cooking performance.

• Supports the oven door with a spring mechanism for controlled opening and closing
• Helps pull the door tight against the gasket for an effective seal when closed
• Works with the opposite hinge to keep the door aligned and stable
• Common symptoms include door not closing fully, sagging or dropping, hard-to-open/close action, or heat escaping around the door

• Disconnect power and allow the oven to cool completely before servicing
• Remove the door following your model's instructions; engage hinge locks or use retaining pins if provided
• Replace the hinge in the same orientation; ensure hinge arms are fully seated in the receivers
• Reinstall the door and verify smooth motion and a complete seal

This oven door hinge restores smooth, controlled movement so the door opens easily and closes fully for a reliable seal. Replacing a worn hinge helps reduce heat loss and supports consistent cooking performance and safe operation.

• Provides the pivot and spring-assisted action for opening and closing the oven door
• Helps pull the door closed and hold it at intended stop positions
• Maintains even gasket contact to keep heat inside the cavity
• Common symptoms of a failing hinge: door won't close fully or sit flush, drops or slams open, binds or pops when moving, or shows an uneven gap

• Disconnect power and allow the oven to cool completely before servicing
• Support the door; open to the removal position and release hinge locks, then lift the door off
• Use caution—hinge springs are under tension; wear hand and eye protection
• Install in the same orientation and verify door alignment and smooth operation after reassembly