Kitchenaid Refrigerator Parts

I ordered a new solenoid valve set and watched the online video of the replacement process. So after emptying my freezer and fridge, removing the doors and freezer drawer, so I could mover the fridge out of its cove, I discovered after taking the panels off the rear, that my fridge is different than that shown in the video. I went back online and discovered in one of the exploded views of the cabinet there is a panel inside the refrigerator which can be removed after taking the shelves out of... Read more

Checked the evaporator fan it wasn't working properly. Replaced the fan all is good Read more

Pulled out storage bin Removed side track rail covers Popped off gear from holding clip Installed drive shaft Installed rail cover and storage bin Only took about 15 minutes Read more

I replaced the drive shaft, coupling and seal and now it works well. The videos were a big help. Read more

Having never fixed a fridge before, I did a little research. The unit was not old & the cooling system was operating. Observing the frozen ice inside, I diagnosed it as the heat rod and/or it's thermostat as bad. I contacted ApplianceParts Pros, who assisted in confirming my theory. IMPORTANT NOTE: the sales advisor Joyce was truly an intelligent, knowledgable professional, NOT some "burger-order taker" usually encountered. This alone speaks VOLUMES. Subsequently, the parts arrived... Read more

• Door won't open or close

Looked for parts online that were worn and compared prices. Best price was appliance part pros. Ordered and received in 2 days and easily replaced worn parts. Read more

Removed the back cover to access the fan area. Clean the area with brush and vac first. Unplugged the Refrigerator. Used a socket set with 1/4" socket. Had an extended and a standard socket. Removed the condensate plastic drain from the bottom of the refrigerator to have more access to the fan. Unplugged the fan motor. Removed the two screws holding the fan in place. Removed the fan unit from the condenser side of the bracket. Place new fan on the fan and installed exactly the way I removed the... Read more

The tech sheet test 56 said the motor wouldn't return to zero. I ordered the "Ice Maker Assy-Lp, and the Valve Assy-Water Dual". On my particular model the ice maker is in the ceiling of the refrigerator box. After removing the water filter and two screws around the drop down water filter door, the right side panel drops down by pulling it apart from 3 plastic pop-ins. Two of them broke when the repair guy man handled it. Pulling easy and supporting the inside pieces is key. Then I unplugged... Read more

No instructions are included with either piece, which makes installation take more time and care. Tools needed: Small standard flat blade screwdriver, box knife or other knife with at least a 2" long blade, super glue. Remove the old main crisper frame: 1. Remove old main frame by lifting upward and outward. 2. Remove the center rail from the frame. May require bending of the main frame to remove it. 3. Remove the crisper front panel by unsnapping from frame. This is easily done by... Read more

Yes exact fit Read more

Replaced the broken parts. The water leak was caused by the drain valve not directed into drain pan Read more

Replaced the defrost thermostat and heater and the refrigerator was working again. Read more

After sliding out the old shelf I removed the middle track from the old shelf & installed it with the new left side track on the new shelf. They basically click in & out. Slid the new shelf assembly in & put meat drawer in place. Read more

Right-side gasket replacement was straightforward. Left side required removal of mullion, which stumped me. I contacted Appliance Parts Pros who gave me the necessary instructions: Remove the center screw and lift up the mullion. Simple enough, once I knew how to do it. Read more

The manual had instructions for pulling things apart, the flaps over the drawer tops and the clear plastic inserts in the shelf. Flaps--Easiest to work with when the shelf is out and upside down. Slide flaps to the side a little to release the axle pin on the flaps from the receptacle hole on the shelf frame. Clear plastic plates are held in with a plastic pin on the side of the shelf frame. Carefully pull the side off the shelf there away from the pin slot until the insert pops out.... Read more

I took apart the old bucket with a screwdriver and put the new one with no problems. Read more