Maytag Parts

The Lint Screen Door is an OEM part for Whirlpool dryers. It is located at the front of the dryer and provides easy access to the lint screen. It helps to trap lint and debris from the drying process, preventing it from entering the dryer vent and potentially causing clogs or fire hazards.

Causes of a faulty or damaged lint screen door can include regular wear and tear, physical damage, or improper handling. These factors can result in issues such as difficulty in opening or closing the door, a loose or insecure fit, or reduced effectiveness in capturing lint.

Symptoms of a bad lint screen door may include:

• Difficulty in opening or closing the door
• Loose or wobbly door fit
• Lint bypassing the lint screen and accumulating in the dryer vent

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Color: white. It measures about 12-1/2 inches wide by 8 inches high.

Color: metallic. Measures about 11 inches wide by 2-1/2 inches high.

This small strainer sits inside the washer's water inlet valve and screens out sand, rust, and sediment from the supply lines. Replacing a clogged or missing screen restores normal fill flow and helps protect the valve.

• Filters debris from incoming hot and cold water before it reaches the valve and tub
• Helps maintain consistent water flow during the fill cycle
• A clogged or damaged screen can cause slow fill, very long fill times, or no fill
• Common causes for replacement include mineral buildup or rust/sediment from supply lines

• Unplug the washer and turn off both water supplies
• Place a towel or shallow pan, relieve hose pressure, and disconnect the fill hoses from the inlet valve
• Carefully pull out the old screen (needle-nose pliers work well); press the new screen fully and evenly into the valve port
• Reconnect hoses, restore water and power, and check for leaks
• Tip: Many washers have separate hot and cold inlets—inspect both screens and replace as needed

Color: metallic. Measures about 10 inches wide by 5 inches deep. Be sure to measure old filter before ordering. If your filter measures approx 11 1/4" x 6 1/8" use R0710163.

Replace a clogged or damaged vent grease filter to keep your appliance drawing properly. This filter captures airborne grease and cooking particles to protect the blower and help maintain effective ventilation over your cooktop.

• Traps grease and particulates pulled through the ventilation stream during cooking
• Helps protect the blower and internal components from buildup
• Supports proper airflow and smoke/odor capture from the cooktop area
• Replace if torn, warped, heavily saturated, or when cleaning no longer restores performance

• Disconnect power to the appliance before servicing
• Open the vent grille or filter access and release the retaining tabs/handle
• Note orientation; seat the new filter fully and latch securely
• Do not operate the vent without a grease filter installed

This factory replacement filter helps protect your appliance's internal systems by capturing debris and contaminants, maintaining proper flow and performance. Replacing a damaged or clogged filter can help restore efficiency and prevent avoidable wear.

• Screens particles from the air or water stream to safeguard internal components
• Helps reduce buildup that can lead to odors, residue, or restricted flow/airflow
• Replace if torn, warped, broken, or persistently clogged
• Common symptoms include reduced performance, unusual noises, residue buildup, or poor circulation

• Disconnect power (and shut off water supply if applicable) before servicing
• Access and removal method varies by model; note orientation and locking tabs or latches
• Do not force the filter; align and seat fully to ensure a proper seal
• Never operate the appliance without all required filters in place; refer to your model's user guide for specifics

The Filter is an OEM part for Whirlpool cooktops. This part is responsible for trapping grease and other airborne particles, ensuring that your kitchen remains clean and free from unwanted odors during cooking. It effectively captures grease and prevents it from accumulating in the exhaust system.

A bad grease filter can occur due to clogging, damage, or excessive wear. If you notice symptoms such as poor ventilation, persistent cooking odors, or visible grease buildup in the downdraft vent, it may be time to replace the worn-out or clogged grease filter with this genuine OEM part.

Symptoms of a bad grease filter include:

• Poor ventilation and airflow
• Lingering cooking odors
• Visible grease accumulation in the downdraft vent

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This refrigerator water filter cartridge replaces the installed filter to help restore clear, better-tasting water and improve ice quality. It's a direct-fit replacement designed for compatible Whirlpool refrigeration systems. What it does:

• Filters water to reduce common impurities that can affect taste and clarity
• Helps improve the quality of ice produced by the refrigerator
• Can resolve symptoms like cloudy water, off-taste, or reduced water flow from the dispenser
• Restores proper filtration performance when the original filter is expired or clogged

• Follow the refrigerator manufacturer's instructions for removal and installation.
• Run and discard the recommended amount of water after installation to flush the system before use.
• Turn off the water supply and disconnect power if required by your model before servicing.
• Inspect the new filter for damage; do not use a damaged filter.

This is a replacement refrigerator water filter cartridge that helps restore clearer, better-tasting water and ice. Use when your dispenser or ice maker produces cloudy water, unpleasant taste or odors, or reduced water quality. What it does:

• Traps common particles and sediment that cause cloudy water
• Reduces chlorine taste and odor to improve water and ice flavor
• Helps maintain normal dispenser and icemaker performance related to water quality
• Provides a direct-replacement fit when the OEM filter is removed and replaced

• Turn off the water supply and dispense water to relieve pressure before removing the old filter.
• Remove the old filter per your refrigerator's OEM instructions and install the new cartridge until it seats securely.
• Run several gallons of water through the dispenser after installing to flush the system and clear air.
• Follow the refrigerator OEM for recommended replacement interval and any filter reset procedures.

This replacement refrigerator water filter helps improve water and ice taste by trapping common impurities. It restores cleaner-tasting water for drinking and cooking when your existing filter is old or clogged. What it does:

• Filters water to help reduce common contaminants that affect taste and clarity
• Helps improve the taste and odor of dispensed water and ice
• Addresses symptoms like unusual water taste, cloudy ice, or reduced water flow from the dispenser
• Restores proper filtering performance when the old filter is past its service life

• Turn off water supply to the refrigerator before removing the old filter.
• Follow your refrigerator's filter removal/installation steps; typically push/rotate or pull to remove and insert until secure.
• Flush several quarts of water through the dispenser after installation to clear air and initial carbon fines.
• Dispose of the used filter according to local regulations.

The Pump Filter is an OEM part for Whirlpool dishwashers. It is a filter that screens debris from entering the pump and wash arms during the dishwashing cycle.

The pump filter is responsible for catching food particles and other residue, preventing clogs and maintaining optimal water flow throughout the dishwasher. It ensures the pump and other internal components are kept clean.

Symptoms of a clogged or damaged pump filter include:

• Excessive noise or vibrations coming from the pump area
• Slow or reduced water drainage
• Built up residue in the filter housing or sump area
• Incomplete cleaning or drying results

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This Whirlpool Water Filter Housing is an OEM part for specific Whirlpool refrigerator models. It plays a role in accommodating the water filter, ensuring clean and safe drinking water is dispensed from your fridge. 

A faulty housing may lead to water leaks, improper filter fitting, or reduced effectiveness in water filtration, affecting the quality of the water dispensed.

Symptoms of a bad water filter housing include:

• Leaking water near the filter area.
• Difficulty in installing or removing the water filter.
• Unusual noise or vibration when the water dispenser is used.
• The water filter does not lock in place securely.
• Noticeable decrease in water flow from the dispenser.

This genuine Whirlpool OEM replacement part is compatible with Maytag, Jenn-Air, and Kenmore models.
 

This fine screen is the small mesh filter that sits in the dishwasher sump to catch food particles and help protect the pump and wash system. It keeps debris from circulating so dishes rinse more effectively. What it does:

• Traps food and debris in the sump to prevent clogging and pump damage
• Helps maintain proper water flow for consistent wash and drain performance
• Reduces risk of food redepositing on dishes during cycles
• Commonly replaced when torn, heavily clogged, or missing

• One fine mesh sump screen

• Turn off power and disconnect the dishwasher before servicing
• Remove the lower dish rack and access the sump area to replace the screen
• Inspect surrounding seals and housing for damage while servicing
• No special tools typically required; handle mesh gently to avoid deformation

this is not a filter. The water filter bypass attaches in the water filter head and allows the water to flow to the dispenser and ice maker when the filter has been removed. Approximate dimensions: 4.37" x 2.87" x 2.5"