Maytag Fuse Or Sensor

The Ice Thermistor Assembly is the temperature sensor your refrigerator uses to monitor the ice maker/ice compartment. Accurate readings help the control time harvests and maintain proper ice room temperature, restoring consistent ice production when the sensor fails. What it does

• Senses temperature at the ice maker/ice compartment and reports to the control
• Helps the control time ice harvests and, on some models, manage ice box airflow
• Can address issues like no ice, intermittent/slow ice production, or ice clumping/melting
• Clear a thermistor-related fault noted in service diagnostics

• One ice thermistor assembly

• Disconnect power before servicing
• Access the ice maker/ice compartment; note original sensor placement and wire routing
• Transfer any clips/insulators if present, connect the new harness, and secure the sensor in the same location
• Restore power and run the unit's ice maker/service test (if available) to operation

This electrical safety fuse opens the circuit when a short or overcurrent occurs. Replacing a blown fuse can help restore power after the root cause is corrected, protecting controls and wiring from further damage.

• Protects the appliance by interrupting power during overcurrent or short-circuit events
• When open/blown, the appliance may be completely unresponsive
• Helps prevent damage to control boards and wiring during faults
• Often fails after a component shorts or a power surge occurs

• Disconnect power to the appliance before servicing
• Use a multimeter to test the fuse for continuity; replace only if open
• Install a fuse with the exact same rating and form factor as the original
• If the new fuse blows again, stop and diagnose the underlying fault; consider service for high-voltage systems

A high-limit thermostat that stops the dryer's heating circuit if internal temperatures get too high, helping prevent overheating and protecting heating components. Replaces a failed high-limit thermostat to restore overheat protection. What it does

• Opens the heating circuit when dryer temperature exceeds the thermostat set point to prevent overheating.
• Commonly related symptoms: dryer runs but produces little or no heat, dryer gets unusually hot, or the thermal cutoff repeatedly fails.
• Works as part of the dryer's temperature-safety system to protect heating elements, fuses, and internal wiring.

• One high-limit thermostat

• Disconnect power before accessing the dryer and work only after panels are cool.
• Take a photo or label wires before removal to ensure correct reconnection.
• Test the thermostat for continuity with a multimeter to confirm failure before replacing.
• If other safety devices (thermal fuse, cycling thermostat, element) show symptoms, inspect and test those components too.

This safety thermostat monitors internal temperature and opens the circuit if the appliance overheats. Replacing a failed high-limit thermostat restores heat and helps protect controls, wiring, and nearby components from thermal damage. What it does:

• Monitors temperature and interrupts power to the heating circuit if an unsafe temperature is reached
• Helps prevent overheating damage to internal components
• When failed open, can cause no heat or cause the unit to shut off during high-heat operation
• At room temperature it should read closed/continuous; an open reading indicates replacement is needed

• 1 high-limit thermostat

• Disconnect power at the breaker (and shut off gas supply if applicable) before servicing
• Access location varies by model; commonly mounted to the oven cavity, plenum, or rear panel
• Transfer wires one at a time and mount the thermostat flush to its surface or bracket
• After replacement, verify proper airflow/cooling and address any root causes of overheating

This time-delay fuse protects the appliance's power circuit by opening when current exceeds a safe level while tolerating brief inrush current. Replacing a blown fuse can help restore power once the root cause is corrected. What it does:

• Protects the line and control circuits from shorts and overloads
• Time-delay design helps prevent nuisance opening during startup surges
• When open, the unit will be completely dead—no display, lights, or response
• Repeatedly opening usually indicates an unresolved electrical fault that needs diagnosis

• 1 time-delay fuse

• Disconnect power at the breaker before servicing; some appliances can retain dangerous high voltage
• Replace only with the same type and rating specified by the manufacturer
• Inspect the fuse holder and wiring for heat damage or loose connections before reassembly
• If the new fuse opens immediately, stop and diagnose the underlying cause; never bypass or upsize a fuse

This cycling thermostat regulates dryer drum air temperature by switching the heater on and off at its rated setpoints. It helps maintain consistent drying performance and protects against overheating for safer, more reliable operation. What it does:

• Regulates heater cycling to maintain target drum temperature during a cycle
• Opens on temperature rise and recloses as the air cools to prevent runaway heat
• Failure can present as no heat, weak heat/long dry times, or overly hot operation
• Operates around a 180F open / 140F close rating per catalog specification

• 1 cycling thermostat

• Disconnect power; for gas dryers, also shut off the gas supply
• Access location varies by model; remove the appropriate panel to reach it
• Note wire positions; transfer leads one at a time and secure the thermostat with the original screws
• After installation, clean lint passages and ensure proper vent airflow to prevent overheating and repeat failures

This element repair kit restores a safe, solid electrical connection to an electric range/cooktop surface burner, helping the element heat consistently and reducing arcing after the original connector has overheated or loosened.

• Repairs a damaged or heat-weakened surface element connection
• Helps resolve a burner that won't heat or heats intermittently
• Addresses visible scorching, melting, or arcing at the element plug-in
• Supports a snug, reliable fit for the element prongs

• Disconnect power at the breaker or unplug before servicing; allow the cooking surface to cool completely
• Match connector orientation and move one wire at a time to avoid miswiring
• Inspect wire insulation and element terminals; replace any parts with burnt, pitted, or loose contacts
• Ensure the element seats firmly after repair and verify proper operation before regular use

This 250V, 1A fuse protects your washer's control circuit from overcurrent. Replacing it can restore control power once the root cause is corrected.

• Opens to protect electronics when current exceeds its 1A rating
• Check this part if the washer has no power, the control panel is dead, or it won't start
• A blown fuse will test open for continuity
• Repeated failure points to an underlying short or component fault that must be fixed

• Disconnect power before servicing
• Access the fuse at the control board or fuse holder
• Replace only with the same rating: 1A, 250V
• Inspect wiring/components and correct any short before restoring power

Primary limit switch that interrupts the heating circuit when temperatures exceed safe limits to prevent overheating. Replacing this switch restores the appliance's temperature safety control and helps return normal heating behavior. What it does:

• Monitors temperature and breaks power to the heating element when the preset limit is reached.
• Acts as a safety cutoff to help prevent overheating and related damage.
• A failed-open switch commonly causes no heat or intermittent heating.
• A failed-closed switch can allow excessive heat or repeated thermal trips.

• Disconnect power before servicing to avoid shock or injury.
• Note terminal locations and wiring before removal; reconnect each wire to its original terminal.
• Handle the part and terminals carefully to avoid damage; secure fasteners firmly but do not overtighten.

The Microwave Thermostat is a reliable component designed to regulate temperature in your microwave, ensuring optimal performance and safety. This genuine OEM part is specifically compatible with a wide range of Samsung microwave models, providing a secure and precise fit. By maintaining the correct temperature levels, the Microwave Thermostat helps prevent overheating and extends the lifespan of your appliance. Installing the THERM thermostat restores your microwaveGÇÖs functionality, allowing you to enjoy consistent heating results every time. Crafted from high-quality materials, this thermostat offers durability and dependable operation, giving you peace of mind with your repair. Whether your original thermostat is malfunctioning or needs replacement, the Microwave Thermostat is the perfect solution to maintain your microwaveGÇÖs efficiency and reliability. Trust in this genuine OEM part to keep your Samsung microwave running smoothly and effectively.

This lower thermostat monitors and helps regulate temperature in the appliance's lower compartment by opening and closing an electrical contact. Replacing a failing thermostat can restore normal cycling and help the compartment maintain correct temperatures. What it does:

• Senses lower-compartment temperature and completes or breaks the circuit to control cooling cycles.
• Helps the compressor/fan cycle on and off to maintain set temperatures.
• A defective thermostat may cause warm temperatures, continuous compressor operation, or inconsistent cooling.
• Matches the OEM function and mounting location for lower compartment temperature control.

• Disconnect power to the appliance before beginning any service.
• Label or tag wires before removal and reconnect exactly to the same terminals.
• Handle the sensor and capillary carefully; avoid kinking or excessive bending. After installation, restore power and verify normal cycling.

This thermal fuse is a one-time safety cutoff that stops heat when temperatures rise above safe limits, protecting the appliance from overheating. Replace a blown fuse to restore proper thermal protection and heating control. What it does:

• Opens the circuit to the heating element when overheating is detected to prevent unsafe temperatures.
• Common symptom: dryer runs but produces little or no heat.
• Can cause dryers to stop heating even though the motor and controls seem to work.
• Helps prevent thermal damage or fire by cutting power to the heater when needed.

• Disconnect power to the appliance before accessing the heating assembly.
• Replace with the exact OEM part; match terminals and mounting location.

Thermal cutoff

This inline fuse is a replaceable safety device that protects your appliance's wiring and components from overcurrent. It restores circuit protection so the appliance can operate safely after a blown fuse is replaced. What it does:

• Protects the wiring harness and electrical components by interrupting power if a short or overload occurs
• Commonly used where a single-point fuse is needed inline with a circuit
• Resolves symptoms like a non-starting unit, intermittent power loss, or a tripped circuit when caused by a blown fuse
• Works as part of the appliance's electrical protection system when installed in the proper harness location

• Disconnect power to the appliance before inspecting or replacing the fuse
• Visually check the blown fuse or use a multimeter before replacing
• Install only in the correct harness location and ensure secure wire connections
• If the replacement fuse blows immediately, stop and diagnose the underlying short or fault

The Thermal Fuse is an OEM component specifically designed for Whirlpool ovens. As an important safety device, it is located near heat-producing elements inside the oven cavity. 

Causes of a bad thermal fuse include overheating of elements or surrounding components over time, which can eventually blow the fuse. 

Symptoms of a faulty thermal fuse include:

• The oven failing to heat or operate heating cycles fully
• Heating elements abruptly shutting off during baking  
• An unusual burning smell emanating from the oven

This genuine OEM Whirlpool part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore oven models as well.