Your privacy choices: We and our partners use cookies for analytics and ads. Decline all turns them off.
Privacy Policy · Do Not Sell or Share My Personal Information
Need Help?
Call
This is the main electronic control board that manages the washer's cycles, motor operation, water levels, and other key functions. It receives input from the user interface and sends signals to the various components to run each wash cycle properly. Replace this board if the washer fails to start, stops mid-cycle, displays error codes, or exhibits erratic behavior that is not caused by a faulty sensor or wiring issue.
This lower wire harness routes power and signals between the control and the components beneath the tub on select 4.7/4.8-cu ft top-load washers. Replacing a damaged harness restores reliable connections and helps resolve intermittent motor or pump operation. What it does:
Replaces broken or cracked drum baffle in front-load washers. Lifts and tumbles clothes during wash cycle. Snaps into drum interior. Easy DIY install.
After doing quite a bit of research and asking appliancepartpros forum if I needed to add a screw when installing, and receiving the answer the next day that is was not necessary, I snapped the part in place and went on with life. Read more
Replacement timer knob for washers. Installs on the control panel to adjust wash cycle settings. Replace if cracked, broken, or won't stay attached.
Replaced with new TIMER Read more
Seals the washer tub to prevent leaks and odors. Replace if torn, cracked, or showing mold buildup. Drum-light version for equipped models. Verify fit.
Replaced the bellow without having to remove any of the panels. Was able to make the repair from the front of the machine by just removing the 2 clamps that hold the bellow seal in place. Read more
The Refrigerator Screw-Tapping is an essential component for maintaining your Samsung refrigerator's functionality. This genuine OEM part ensures precise threading, allowing screws to be securely fastened without damaging the surrounding materials. Designed specifically for Samsung refrigerators, it guarantees a perfect fit and reliable performance. Whether you are replacing a damaged screw-tapping or performing a repair, this Refrigerator Screw-Tapping simplifies the process, saving you time and effort. Its high-quality construction provides durability and long-lasting support for your appliance. By choosing the Refrigerator Screw-Tapping , you ensure your refrigerator remains sturdy and functional, enhancing its overall lifespan. This genuine OEM part is easy to install and seamlessly integrates with your existing setup, making it an ideal choice for DIY repairs. Trust in the quality and compatibility of this Samsung part to keep your refrigerator operating smoothly and efficiently.
The start button had been tricky to use. You had to push it in just a certain way to get the dryer to start. Eventually it was non-responsive. All other controls worked and there was no error code displayed. The repair was to replace the whole control board which cost around $100. Heavy sigh.. Be sure to keep track of all your screws. BTW it was not the thermal fuse. All the online videos say this is the first thing to look for when the dryer will not start. Be sure to check with the person... Read more
Fix a washer that won't advance through cycles, stops mid-wash, or skips stages. This mechanical timer controls wash, rinse, and spin sequences.
Took out old timer, and upon inspection notice some electrical arcing( burned areas). I installed new timer and worked perfectly. Problem was that it would fill up with water, but after it was filled the timer kept going but washer was not agitating. Only thing that worked was delicates wash. Important Disconnect/ unplug power cord! 1. Remove knob, center cap pops off revealing a pin. Slide that off and the knob should come off. 2. Removing knob should reveal 2 socket screws remove... Read more
Adjustable leveling leg threads into the washer base to support and stabilize the unit. Replace if cracked, stripped, or missing to level cabinet.
Replacement water fill hoses for washing machines. Connect home water supply to washer. Replace when cracked, leaking, or showing rubber wear or corrosion.
Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a... Read more
Fixes poor cleaning or no agitation in top-load washers. This washplate impeller creates wash action. DIY-friendly repair, typically 30 minutes.
New wash plate and new bolt Read more
Dispenser drawer handle broken or cracked? This white washer handle attaches to the detergent drawer. Easy DIY fix with basic screwdrivers in minutes.
Ordered and installed a new handle and dispenser drawer Read more
Cap seal creates a tight barrier between cap and mating surface to prevent leaks. Replace when worn or damaged to restore secure fit. Confirm compatibility.
Background - Wife and I are 78 years old. Since there is no budget for new or repair we did it ourselves. I have COPD and could no have done it without her help. Watch you tube examples and followed them. replaced the coupler motor to trans and since we were there replaced the clutch and agitator kit. Also replaced hoses with new stainless hoses. Just tested and everything seems to work as new. Not bad for a machine 12-15 years old. I looked at new ones but the EPA has turned them into... Read more
This is a small mesh filter screen that fits inside the water inlet valve to catch sediment and debris from your household water supply before it enters the washer. It prevents mineral buildup and particles from clogging or damaging the valve internals. Replace this screen if your washer is filling slowly, not filling at all, or if the screen is visibly clogged, torn, or deteriorated.
Ordered a replacement valve and installed it. The part from AppliancePartsPro was an exact replacement for the original part. Replaced the hot and cold hoses at the same time to insure no leaks. Cold water settings now work properly again. Read more
If your washer won't fill with water or fills slowly, the inlet valve likely needs replacement. This assembly controls water flow into the tub. DIY fix.
Washer needed a water in let valve. It was very easy !! Read more
This is an electrically controlled water inlet valve that opens and closes to allow hot and cold water to flow into the washing machine during the fill cycle. It connects to the household water supply hoses at the back of the washer. Replace this valve if the washer is not filling with water, fills slowly, continues to fill when turned off, or leaks from the back of the machine.
Researched, then decided to try everything suggested. Cleaned the hidden filter under the washer, checked the lines and the water inlet valves, opened it up and found a hose rubbed thin because it wasn't clipped correctly during the manufacturing process. Replaced the inlet valve, pressure sensor and the thinned tube (all parts except the hose from appliance parts pros.com-had to get the hose at the car parts store). Machine has not worked this well in years, and saved hundreds in labor. Your... Read more
If your washer agitator won't engage or spins weakly, these cam rollers may be worn. Kit includes 4 rollers. Easy DIY repair for most home mechanics.
A buddy of mine gave me a washer and said if you can fix it you can have it, It doesn't spin. I tried running a spin cycle and found that it did try to spin but was very noisy. I disassembled the washing machine and found that the tub seal had gone out and took out the bearings with it so I ordered a new tub and seal kit and while I waited for that I proceeded to disassemble the rest of the washing machine and clean everything so when the new parts arrived it was ready and waiting. Bearing... Read more
Opt-Out Request Honored
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.