Maytag Washer Parts

Used the parts and youtube video from your company. Read more

Replace the drum drive belt and tension pulley assy. Read more

This was the second attempt at fixing this problem. The first repair and parts were generated by listing the problem and reviewing the potential corrections, listed on the web site. From making repairs on other clothes washers, I was confident that some of those potential causes could have been the cause. Unfortunately the counterbalance spring and suspension springs were not the cause as they were attached as intended and in good condition. I reached out for Appliance Parts Pros input... Read more

• Won't start

I removed the belt and found with no load the motor ran but made a grinding noise. I purchased a new motor and installed it. The fix was easy and quick. Read more

18 year old Maytag Atlantis top load washer had a load knocking and rattle sound with excessive vibration when the tub was spinning, but not when it was agitating. They was no water leaking. I took the front panel off and carefully listened while I ran a cycle and the loud sound sounded like it was coming from the drain pump. So I took off the drive belt and noticed that it was glazed and that there was belt material on the drain pump and tub transmission pulleys. I removed the drain pump and... Read more

• Will not agitate
• Pumps but will not spin

I had previously replaced the pump about 1 year ago. That was not the problem. Still leaked the same way - intermittently, but always in the center of the washer onto the floor. None of the hoses were leaking - no evidence of corrosion or water mineral residue at any of the hose fittings. So, it must have been something else. I studied the parts diagram for the washer tub assembly and concluded the source of the leak almost had to be the outer tub's Centerpost Gasket. It was really the... Read more

As a Mechanic, I did the common sense approach: INITIAL OBSERVATIONS & CHECKS: - Unplug Machine & check inlet water hose connections for leaks and signs of hose failure; - Remove back panel & inspect for water presence at all hose connections, pump, bottom of basket (bottom center of basket where the main motor, shaft bearing, and tub seal is located), dispensers, bottom of wash basket, water injector area, look everywhere where there is a hose connection and where water flows... - Inspect... Read more

• Will not fill with water
• Will not stop filling with water

This should be plastered all over the place and every owner of a front end washer should be advised or a recall should be issued about this. As I opened the top of my washer to fix a F35 error by replacing the water level switch, which worked out great and it fixed the issue, I noticed a rusting spot at the bottom of the washer just under where the motor is placed. After running the washer with the lid open (I don't recommend doing that) I noticed that it was coming from the top of the soap... Read more

The ridges inside the agitator base were stripped. Installed a new base - after a good cleaning of build-up on the spindle. Works like new! Read more

I purchased the lid latch assembly and the lid switch strike. Following the clear video instructions for each part, my handy teenage son was able to remove the lid latch assembly and replace it with the new part as well as the lid switch strike. The washer is back to working perfectly for under $100. Appliance Parts Pros carry the parts to repair and at a lower cost than other online retailers. I saved about $30 compared to the other online site and I saved a service call fee. I'm so glad I... Read more

We watched a YouTube video on how to replace the door latch. Very simple to do. We had to remove the metal band holding the door gasket to be able to access the latch. After removing the band, we pushed aside the gasket and removed the screws to the latch and the connecting cables. To install the new part, we just reversed the process. We reconnected the cables, inserted the new door latch and screwed it in. The hardest part of the process was getting the metal band around the gasket. It... Read more

I read through the issues related to my problems. I purchased both parts so if one was fixed then the other still needed to be fixed I would have the part. I watched both videos for replacing the parts which made things so much easier. I will say prying in the front clips was the biggest issue out of the whole repair. I repaired the suspension issue by replacing the 4 rods. The very last rod that I replaced was indeed bent. I closed the top and ran one load and then the lid lock issues... Read more

Ordered and replaced bellow. It is important to supply the correct model number as my machine is a later model than the one used in the training video. The front panel is one piece, rather than two. Additionally, several of the fasteners were hex head screws, rather than torks. The Bellow is somewhat different having an opening for the light fixture. That said, the video was adequate to get the general idea of how to remove and replace the bellow. I found it very difficult to replace... Read more

Bought new Transmission/gear box. Putting in the new one was easy. Taking the old one out was a nightmare. The corrosion on the spanner nut and drive block was awful. Ten years of VERY hard water and six kids made for a lot of corrosion and hard water crystallization. I do not own a spanner wrench. I am not sure having one would've helped. I tried pipe wrenches, needle nose vice-grips and many other ways. What eventually worked was taking a three inch ratchet extension, putting it... Read more

• Lid or door won't close
• Lid or door will not open

I removed the two screws and all the pieces that were broken. Went online to Appliance parts.com, searched for the part using the model number from the machine and ordered the part . part arrived in 2 days and with a Phillips screwdriver was installed in less than 5 minutes. Read more

First I check with Appliance Part Pros, watch videos how to access the parts I believe to be the problem. I love there videos and parts list of solutions to fix what it wrong. First I removed the washer from the laundry room and but it in the garage for more room to work on it. The next thing I replaced was the door lock which seem to be a possible cheap fix and does get a lot of abuse, however it was not the door lock and people should stop posting it could be this issue when they get a F06... Read more