Maytag Washer Parts

I ordered what I thought were the necessary parts from appliancepartspro.com as my washing machine wouldn't spin. I should have watched there videos before I began as I took the whole cabinet off and everything and after receiving the parts and watching their video realized I didn't need to do so, at that point in time. When I put the pieces back together I found that the tub was really stuck, it would move but for the most part it was hard to move and creating a horrible noise. I knew I... Read more

The washer would try to start. The door would lock, but then would get stuck in the phase of start-up where the drum needs to roll around (I assume so it knows what's in there). It would sit and think about it for a couple minutes and then give the error codes. I shut it off (sometimes had to unplug it and plug it back in), and it would take about 10 minutes for the door to unlock. After reading about fixes, I decided to dive in and try it (the washer is only 3 years old and I'm pretty... Read more

Installed new Water Inlet Valve. Read more

Found the parts on appliance parts pros and ordered them. It was amazing one arrived the next day and the other just the day after that it was so quick! There wasn't any real assembly just pulled the old drawer out and put in the new one! Read more

Just like the one's I have worked on for 30 years for Whirlpool. Read more

Removed the screws, lifted the old lid out of the hinges. Replaced the hinges, set new lid in the hinges and replaced screws. Read more

• Shakes and moves

We looked online at AppliancePartsPros.com under the symptoms and found it was most likely caused by the shocks. Of course there was a repair video showing how to replace all four shocks step by step, and there was a link for purchasing the four shocks at the bottom of the video. Our repair didn't go quite as quickly as on the video because we are novices, but we were able to do the repair ourselves and, once again, saved ourselves a ton of money! Now we have a very quiet washer and dryer again... Read more

Used the parts and youtube video from your company. Read more

Ordered the part, which was easy and smooth. Watched you tube video on how to repair. Took me 15 minutes. Easy as it could be. Read more

• Lid or door will not open
• Won't start

Did lots of internet research. Narrowed problem down to three things - door lock latch, control unit, and motor control unit. Figured out how to run the diagnostic test program, which showed a F22 (door lock) error. Removed and ohm tested the door lock (pins 1 & 3). Found door lock latch to be defective. ordered new one and installed it. YouTube video helped a lot. https://www.youtube.com/watch?v=_SjU6k5bpSs So far, so good. Have only done a few loads. New door lock latch tested fine. Read more

I had replaced the Agitator cams a couple of times already due to my brother-in-law overloading the machine which stripped the teeth off of the cams. I also noticed the agitator seemed to 'wobble' and made 'knocking' noises quite a bit. I reviewed the video on the Appliance Parts Pros web site, disassembled the agitator and cleaned everything up, which helped a little, but not enough. Figuring the agitator itself was worn out also, I looked up and ordered all the parts for the upper agitator on... Read more

Replace the drum drive belt and tension pulley assy. Read more

I read through the issues related to my problems. I purchased both parts so if one was fixed then the other still needed to be fixed I would have the part. I watched both videos for replacing the parts which made things so much easier. I will say prying in the front clips was the biggest issue out of the whole repair. I repaired the suspension issue by replacing the 4 rods. The very last rod that I replaced was indeed bent. I closed the top and ran one load and then the lid lock issues... Read more

The ridges inside the agitator base were stripped. Installed a new base - after a good cleaning of build-up on the spindle. Works like new! Read more

• Won't start

Not wanting to spend hundreds of dollars on an appliance technician's service call, I searched online to troubleshoot the problems with my particular Maytag Washer Model Number MVWX500BW0. I stumbled across AppliancePartsPros.com and investigated there the most likely causes for my Maytag Washer's not agitating properly and not spinning at all. In order to acquire some additional information, I telephoned AppliancePartsPros.com and spoke with an extremely professional, knowledgeable and helpful... Read more

• Will not agitate
• Pumps but will not spin

I had previously replaced the pump about 1 year ago. That was not the problem. Still leaked the same way - intermittently, but always in the center of the washer onto the floor. None of the hoses were leaking - no evidence of corrosion or water mineral residue at any of the hose fittings. So, it must have been something else. I studied the parts diagram for the washer tub assembly and concluded the source of the leak almost had to be the outer tub's Centerpost Gasket. It was really the... Read more