Maytag Washer Valve

• No hot or cold water
• Will not fill with water
• Will not stop filling with water

Replaced the water valve. Easy repair. The repair video was spot-on. Tools needed: Slip joint pliers for removing and attaching the hoses and moving the hose clip. 5/16 nut driver. Phone to take a picture so I could get the wires put back right. Shut off the water and unplug from power. Remove the hoses. Using a 5/16 nut driver remove the single screw that holds the bracket, lift bracket slightly and pull from the washer. There is a little slack in wires and fill hose to work with. Take a... Read more

Remove the top panel by removing 3 hex nuts on the back of the washer. Inlet valve was located right underneath the panel towards the back. Remove one screw using a t20 bit and unplug the 2 plugs located on the valve. With a pair of pliers removed a tension clamp and the valve comes right off. Read more

Saw the drip, ordered the part. Unplugged machine from wall. Torx bit on my DeWalt cordless drill to remove the screws securing the lid to the machine, lifted off top cover. Turned off water supply and removed the water supply hoses from back of the machine, used needle-nosed pliers to remove spring clamps from the defective part, removed mounting screw for defective part at rear of machine. Worked the defective part out of mounting, unplugged the three electrical connectors. Then, plugged in... Read more

Replaced water inlet unit. Read more

• No hot or cold water
• Will not fill with water
• Will not stop filling with water

Ordered a new inlet water valve . Super fast delivery ordered on a Wednesday afternoon was here Thursday morning , standard shipping , I was impressed !! Removed the old valve , installed the new , checked for leaks no issues , washer is back on line and my Honey is very happy with me . Read more

• Will not fill with water

I ordered this new valve, and voila!!! No more using up all the hot water to wash everything. Now I can do all of my laundry with cold water, like I prefer to. Read more

My 15 year old whirlpool washer top was rotting away and my wife was about to buy a new one. a 1 min search on google brought me to this site and within 5 mins found all the parts I needed, Received my order in 3 days and now we're back in business for a total cost of $159 instead of $500 to $600. Will use this site again and have told a few people already. Thanks Rob Read more

Replaced both hot and cold water inlet valves. Works like a charm, issue resolved. Read more

• Will not fill with water
• No hot or cold water
• Will not stop filling with water

I called Appliance pros and asked for a diagnosis. They gave one and sent me the part. It took 15 min. and it worked perfectly. Also got super fast delivery on the part. Thank you!! Read more

Took machine apart replaced valve assembly. Read more

Called a repair man after not being able to determine the exact problem. Narrowed it down to valves, level switch or mother board. Repairman took money for parts and then said he couldn't find them. Went online and found this site, ordered parts Monday, had them by Thursday noon. Had machine running by 1. Read more

Water became visible as it accumulated at the bottom rear part (the part that is tilted back) of the washer drum. I theorized that the valve controlling water flow into the machine was to blame. I began my troubleshooting by going to Appliance Pros website where I looked for a Water Inlet Valve. I easily found this on the exploded parts diagram. After identifying the part that seemed to be the issue, I began reading other reviews from folks who were experiencing the same problem and who solved... Read more

Remove the two valves at back of washer, only 4 screws, remove the electrical clamps, replace with valves, easy, 20 minutes to fix, and a woman did it, saved $320.00, yahoo Read more

• Will not stop filling with water
• No hot or cold water

Appliance Parts Pros I've used in the past and will continue to use, now they have a video showing step by step how to change the part your going to purchase, video also explains what the part does and symptoms of bad existing parts like mine. Washer machine was dripping water into tank when not in use, it was the water inlet valve. I purchased on a Sunday and it arrived with our mailman on Wednesday. I watched the repair video one more time and changed it out. When you unhook hoses to remove... Read more

Removed the front panel and removed the screw from the console which revealed a broken plastic tab on the right side of the old injector. Replaced the old injector with the new one and that took care of the problem. Read more

• No hot or cold water
• Will not stop filling with water
• Will not fill with water

Purchased replacement fill valve. Read more